I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
HI,
I am using nRF52832 and SDK 14.2 and trying to send MPU accelerometer values to android device through BLE . But when I call " mpu_init() " in main function to initiate...
Dear Sir,
I am new to Nordic. This is my first query. It is related to running Timer with softdevice. I am using TIMER1 ( as const nrf_drv_timer_t TIMER_LED = NRF_DRV_TIMER_INSTANCE...
Hi, Support team,
When I use the SPI peripheral communicate with nrf24l01+,it's no data return in m_rx_buf by using the API nrf_drv_spi_transfer(&spi,m_tx_buf,1, m_rx_buf...
Hi,
I use the FDS on our project firmware. The firmware saves some configurations to FDS at shutdown and the factory reset. At this time, sometime fds_gc() does not call...
Sometime, the timer handler is not call immediately after calling app_timer_start().
environment - nrf52840 - SDK 15 - with FreeRTOS - timer task priority is higher - timeout_ticks...
Hi,
In the nRF Mesh mobile app, when you go to the settings tab, you can hit "Reset Network", this appears to clear any previously provisioned network, and lets you start...
Hi all!
We've been time-stamping GPIO events using PPI in nRF52 , and it works* !
...but when using the SoftDevice , it apparently clashes with the PPI about 30ms after...
Hello,
I have been having issues when using the UART libraries (app_uart.h) with certain pins on the nrf52832. Previous iterations of our project have worked correctly but...
I am investigating an H4 HCI over a UART implementation for a client which plans to use the 52832 (or 52840) as a replacement for a TI BLE chip in a new design.
I have built...
Hi all
We are using customized board with nRf52810 chipset.
Actual requirement in our project is to send 100 bytes of data for 10 millisecond.
Kindly suggest a procedure...
I'm developing multiple peripheral and a central. Central is only scanning and Peripherals are only advertising.
In the example, I see that I should use the ble_app_blinky...
Hi,
I was trying to run dfu mesh example according to this. I attempted quite few times but every time having an error at step 11.
infocenter.nordicsemi.com/index.jsp...
Hi, Nordic Team
My development environment is PCA10028, SoftDevice 130, SDK12.3.0
I use a s130_nrf51_2.0.1_softdevice.hex.
It is based on ble_app_multilink_central and...
I am new to Nrf52832.......I have started development of a custom board based on Bt832 and BT832X.
I have built 2 proto boards one with BT832F and the other with BT832X...
Starting idle task using Task Manager library frequently throws error "Unknown function at 0x000008C8" when running with the debugger (often takes several restarts until it...
