Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi
I am trying to add the secure DFU bootloader (BLE) code to an existing application for the nRF52840. I'd like to send the logging information over UART. What are the...
Using a nRF51802, but can't find data about actual reset level other than min. VDD 1,8V ?? (Page 34 in datasheet )
I need to know actual reset level (VDD) for both rising...
Hi to all,
i am developing a device with NRF52840 DK, in my device i had implemented a service that has some characteristic with noti/read properties. notifications work...
Hi when I try create an account on www.nrfcloud.com on a desktop using Microsoft explorer it doesn't move forward and states "fetch" not defined. Any thoughts?
nRF Toolbox scanner code does not seem to discover devices which advertise a 128-bit service UUID.
I have extended the Template app (within nRF Toolbox) to interact with...
Hi to all,
i am developing a device with nrf52840 soc and i want connect to Windows 10 though ble connection. in my device i had implemented an HID service that should act...
Hey is it possible to use advertising beacons together with an server or there will be some collisions in message reception ?
what i want to do is: setup a mesh which consist...
Is there some guide to help implement UART using nRF Toolbox source code for ios?
I am trying to figure out how to use:
Scan, connect, pair and UART
Any help apprec...
when performing db discovering using a peripheral nrf52832 (running sample dfu project) from sdk 13 from a nrf32832 central on sdk 14 I notice that the db discovery event...
Hi Sir
I would want to download code to Ublox NINA-B301 by command line, but it looks not working, please help.
nrfjprog.exe -i 483064601
nrfjprog.exe --family NRF52...
Hi,
I'm trying to perform a DFU firmware update via command line using nrfutil dfu ble.
The same update using nRF connect works fine. The dongle is flashed with connectivity_1...
I would like to have a ZigBee stack running on the 52840 and use door/window (contact) sensors as well as motion (PIR) that are available on the market today to connect to...
Dear Sirs!
I use compiler IAR 7.80 with Nordic SDK 12.2
Softdevice
s132_nrf52_3.0.0_softdevice.hex
I have very strange issue in debugger.
Break point works, but...
Hi folks,
I try change blinky code for nRF52810 SoC. I must create own timer. I dont know app_timer example help for me?! I want to do when power on leds on 2 seconds...
Hi All,
I am developing an application in which i am interfacing the nRF52832 with an ADC via SPI.
I am doing channel multiplexing (2 channels) such that when i get data...
