Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I've seen many posts asking this question, but with no definitive answer. I've seen latencies for various GPIOs acting as either SPI or TWI, but no baseline interrupt latency...
Has anyone modified the spi_master_using_nrf_spi_master example (or otherwise gotten) the Crystalfontz CFA211TFH 128x64 panel running w/o mods on the nRF52 DK? I have a panel...
Hello,
I captured following data using a Bluetooth dongle for WIN 7 and a Bluetooth keyboard . I also used Wireshark with USBCap driver to capture data going from BT Keyboard...
With my sparkfun 52832 board, when I use the __WFI instruction and I set my device to generate interrupts on P04, the code returns when an interrupt is generated. With the...
We created a custom made board with an nRF52832 and an LIS2DH accelerometer. The board is working fine when it is being powered from a power supply with 3V but when it is...
Developed with SDK 15.0.0. and s132_nrf52_6.0.0_softdevice
After I generate the DFU package, and upload it with nRF Toolbox, it will returns " Upload failed: REMOTE DFU...
SDK 15.0.0, s132_nrf52_6.0.0_softdevice
I have followed the instruction below:
https://devzone.nordicsemi.com/f/nordic-q-a/29067/installing-micro-ecc-issue/115222#115222...
Hello,
Nrf52832 ibeacon broadcast signal is unstable, and the rssi deviation of left and right upper and lower signals before and after the detection of the same distance...
Hello,
I'm working on some LED sequences using the NRFX PWM driver and I can't get the durations I want right.
Let's say that I want a semi-blinking LED (100% - 50% -...
HI
platform:
sdk:15.0.0
52840
\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10040_uart_debug
I want encode(uart) dfu packet not by nrfutil:
(nrfutil...
In my design, I am using a module based on the NRF52832, with a specified LF clock accuracy of +/-250ppm. In my application, I am using v15.0.0 of the SDK with SoftDevice...
hello, we would like to know which development environment Nordic Semi supports/recommends for NRF52832-QFAA-R (except GCC) Is there a special offer from a manufacturer (e...
I'm in the process of scoping out a new project that is in the realm of robotics. It involves one wireless controller that a person would use to turn and drive four wireless...
Hi there,
I have found a similar thread that dates back from a year ago ( https://devzone.nordicsemi.com/f/nordic-q-a/29073/altering-qspi-address-mode ) but I would like...
I created a application that sometimes uses the BLE for 10 seconds. To turn on the BLE I'm using the function
and to turn off the BLE I'm using the function
I already...
