Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi Everyone,
Pardon me if i write some illogical stuff. Complete beginner to this microcontroller.
I started using nrf52832 with Zephyr OS . I was trying to configure...
Hi,
I wished to test multiprotocol with one software but I was wondering if it was possible to compile an application which could switch between zigbee and Thread (and...
I'm using arm-none-eabi-gcc 7.2.1 with nRF5_SDK_15.0.0_a53641a with soft device s140_nrf52_6.0.0_softdevice.hex I'm trying to modify one of the bluetooth examples to add a...
Dear Sir,
I use nrf5_SDK_for_Mesh_v2.0.1_src.zip and test proxy server project,
I scanned the device nRF5x Mesh Light (0x1827 Service), I click "Discover services",...
Hi guys
I am trying to program a nrf51822 module but it is not recognized by the development kit.
These are the pins that I am using:
I can not see the...
Hi,
I am using nrf SDK version 12.2.0
The following code fails to produce event for twi transfer complete const nrf_drv_twi_config_t config = { .scl = I2C2_SCL_PIN,...
I'm using the P20 connectors in nRF52 PDK to flash my custom nRF52832 board.
The connections are like this:
SWDIO ----> SWDIO
SWDCLK ---->SWDCLK
VTG ------> VDD
...
Hello,
We have an application with a S132 device, SDK 14 and Softdevice v5.0.0. On some devices, an assert is being thrown in the sleep prepare function. This is the line...
There are errors on Thingy52 "ble_app_thingee_s132_pca20020.emProject" which I built on SEGGER Studio for ARM V3.34 (64-bit) running on Windows 10. Please advise. Thanks....
Hi!
I'm using an NRF51822 as a GATT client to write data to a characteristic. The peripheral responds with several 20 byte indications. When I receive the indications, the...
Hi, I am importing a bootloader project that uses softdevice s110 and NRF51822 from Keil to Segger Embedded Studio. I have got all kind of errors during the process and I...
Hi Team,
In BLE5,
1) Can we connect a peripheral device to multiple central device?
2) Is it possible to check if connecton fails with any central device in perpheral...
I'm trying to put thingy_sdk_v2.1.0 and 10 nrf52832 boards. I'm compiling "ble_app_thingee_s132_pca20020.emProject". I don't know why it's always an error. How do I demonstrate...
Hi,
I'm using nRF52832 and SDK 15 and IDE im using is Segger studio.
i have ported the uart code into Ble_app_multilink_central.When i debug the code it is getting stuck...
Looking for an example on how to advertise for 10 seconds then go into sd_power_system_off. Trying this by using ble_app_template (s112, ses, sdk15.0, custom, 1 led, 1 rgb...
