I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am trying to test the fatfs example (SDK14) using the 10056 DK.
I do nothing modification and it results in...
<info> app: FATFS example started. <info> app: Initializing...
I realize I am like the hundredth person to have this problem but all the solutions I have found don't seem to work.
I am trying to add a simple header file to the nordic...
I am new to Nordic, I am able to compile and run examples on nRF52-DK.
I know there are examples are done for us but how I can develop my own project which use multiple...
I just replaced SDK 14.0 with the shiny new SDK 14.1 in my project. My project uses components from the SDK, but I don't use the exact same structure. Once again, it won't...
My Environment
Nrf52840
SDK : nrf51_15.0.0
soft device : s140
Target : Scanner (central)
I am trying to set GAP parameter for listening single channel that is...
i use sdk14.2 52832 i use uart
UART0_CONFIG_USE_EASY_DMA =1 consumption ~2.1mA
UART0_CONFIG_USE_EASY_DMA =0 consumption ~650uA
Is this a normal phenomenon, is it true...
Hi,
I have a Development and Evaluation board by Waveshare and i have a nRF51822 board. I have downloaded the nRFgo studio and i have used a USB to UART board and connected...
Hi
I am developing an application where nrf52 acts as a BLE central
Specifications requires that this node should connect to a peripheral with a specified name, obviously...
I have 2 services are running using 16 bit UUIDs and now I am adding another service using our_service.c and our_service.h files but my program is crashing and leading to...
Hi Everyone,
I want to use the QSPI protocol to write data into the external 64Mb of Flash memory provided onboard of nrf52840 PDK.
I am able to run the QSPI example alone...
Sorry Nordic engineers , I'm asking urgently , goods need to come out quickly
chip：nRF52810
SDK：nRF5_SDK_15.0.0_a53641a
examples：ble_peripheral \ ble_app_uart
external...
The iOS source code located here github.com/.../IOS-nRF-Toolbox does not build.
I'm trying the debug the app code in Xcode but there are missing files:
"nRF Toolbox...
The production line is waiting ， I'm sorry to ask that it's urgent
This debug tools display nRF52810 UART Tx is Successful
If I add the code
case APP_UART_TX_EMPTY...
