I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hello I originally wanted to use esb_ptx/esb_prx but the packet could not be changed to 128 bytes! Compressing data packets is inconvenient! I use radio to achieve my project...
I am using Segger Embedded Studio and the nrf52840 development kit.
I can run the BLE peripheral examples using SDK 15 and s140 V6 "blinky" and " cscs" .
but the ble_app_rscs_pca10056_s140...
Checking if this is possible and how to complete.
For the ble_app_beacon example, I'm able to reuse #define APP_DEVICE_TYPE 0x02, to be #define APP_DEVICE_TYPE 0x0E, 0x06...
Hello ,
we are new to BLE
1. We make a long life temp and light sensor , just only transmit from the Nrf to mobile (one way ) , we would like :
1.1 sensor always be...
Hello Noric Dev Zone members,
we are looking for a Firmware developer supporting us in bringing Hyko to our customers.
What we are working on is making energy heroes in...
Hello,
For my project, I want to be notified when my device changes the value of my characteristic so i used the HealthThermoDemo example.
here is my code :
But despite...
Hi , I want to use two GPIO oin with button press hadler even . when pin low will interrupt and into handle..
Below is the code for the single key.
Thanks.
Pa...
This is somewhat of a continuation of this topic:
What does APP_BLE_CONN_CFG_TAG do?
Softdevice 132, header: ble.h: SVCALL(SD_BLE_CFG_SET, uint32_t, sd_ble_cfg_set(uint32_t...
I'm using RFduino that utilizes nRF51822. I need to set a timer1 as timer0 is used by the BLE stack, so I used the following code:
#define TRIGGER_INTERVAL 1000 // ms...
Hello,
Today I had a case where I tried to perform a bootloader-only DFU on a device with a debug version of the bootloader, but instead of trying to replace it with another...
Hi Technical team,
I want to use nrf52832 for my project, below are the some doubts i have with nrf52832
1) nrf52832 will act as HUB and receive data from peripheral...
Hi,
I have already working code in nordic sdk 13.1 with eclipse. But we are move to latest sdk v 15.0 for example of central and peripheral. Now every thing i have modified...
After a node successfully provisioned in the Mesh Network. If I want to unprovision the node, what procedure is needed to make it?
Should I remove all the netkey, appkey...
Hi, I have a problem with the usb HID examples in sdk v15.0 on a nrf52840 Preview DK. I cannot get them working together with a Linux or WindowsCE based USB Host, with Windows10...
Hello.
I'm modifying the Eddystone Beacon Application example. For now, I can transmit my own Eddystone frame. This frame is static, and the board starts transmitting it...
