Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
This link source.android.com/.../services seems to indicate that L2CAP CoC is available in Android 8.x but support may vary by device vendor. Does anyone know how to verify...
Hi,
I just installed the latest NRF5 SDK - nRF5_SDK_15.0.0
and trying to run examples such as "examples\ble_peripheral\ble_app_hrs\pca10056\ser_s140_spi_5W"
But for...
We are developing a bluetooth product that operates on a battery where every uA counts and I have a couple of questions about current consumption in System On Low Power mode...
I am creating a BLE beacon scanner, using nRF51822 and SDK 12.0.0. My beacons will be using public addresses so the upper 3-bytes of device addresses of all my devises will...
Hi,
in our application we will have a main MCU and a second MCU, an nrf52832.
We need to update the fwon the nfr52832 from the main MCU using a bootloader, via UART. ...
Hello,
I want to use 2 SPI bus with nRF52832 IC and SDK5. I can use the "SPI example" for first SPI bus. For the second SPI Bus, I think that I need to modify "sdk_config...
My devices require calibration and self test to be carried out after programming. To implement this, my device checks the JLink reset pin (configured as a GPIO on my NRF52...
Hi everyone, I'm trying to implement a simple bluetooth beacon which broadcasts / advertises the number of button presses and the time in seconds after the last button press...
Hi everyone,
I'm trying to change the advertisement data while advertising using an interrupt. So far I've managed to use a button to change the advertisement data.
...
Hi,
I have huge BLE carrier frequency drift, which cannot pass FCC requirement.
The drift is 256kHz which seems not normal.
I'm using 32MHz 10ppm xtal so drift should...
Hi!
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
In my application I am using Peer Manager to manage bonding and also...
Hi all
The errata sheet V1.8 states that the errata 143 applies also for the Bluetooth Low Energy mode. Does that mean that the BLE stack of the SoftDevice S132 is also...
Hi,
I am using nRF52832 DK and other same custom board, sdk v15.0 with SES IDE. My application like this:
For ble peripheral used example ble_app_uart and for central...
Hi Sir,
In my system (windows 7), I had install the GCC 4 .9 2015 q3 for SDK 14.2.0/12.3.0.
As reference the release note of SDK 15, the GCC upgrade to 6-2017-q2-update...
Good Morning Team, Hope your day is going well! Can you please provide the Full Material Disclosure (FMD) document for below part since I could not locate it on website. ...