In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hi,
I'm able to run the DFU mesh from the quick guide and now I want to integrate the DFU into my application.
My application is based on the light switch example, so...
Please help me fix my computer to allow nrfStudio to program pca10056.
I just received 2 pca10056 1.0.0 2018.35.
I am on 2 computers A and B: both with windows 10 64bit...
I trying to debug an interaction between using SPIM3 on the nRF52840 and the BLE stack in the SoftDevice . A reset is happening, which I think is being generated by the SoftDevice...
Hi I have an application where ESB will be used in the same environment as a few BLE devices which are also our devices. My plan is to set an rf_channel for ESB and then at...
We have an application where we have a large number of sensors, some relay nodes and one or more gateways. The sensors and relay nodes are provisioned by the gateways and...
Hi, I can normally log with NRF_LOG_INFO(). But if i enable softdevice (bluetooth stack init) logging stops working. Interesting part is that there are several log lines before...
BLE Control by Main CPU (MCU):
1. How the MCU communicates with BLE HW?
2. What is the amount of MCU performance is required to control the BLE? (expected answer example...
Hi nordic.
I use SDK 14.20 and nrf52840 board and s332 softdevice.
Our app has to use ant+ and ble.
My device connect with app.
App requests device to ant+ scanning...
hi guys:
When I was using mesh sdk, there was an error in compiling.
I use examples\light_switch\server\light_switch_server_nrf52832_xxAA_s132_6_0_0.emProject
I am...
Hi,
I am using SDK 14.2 -> BLE peripheral proximity example. I was trying to add a custom service and some characteristics to this proximity example. I basically took the...
Hi, I have two strange problems regarding the NRF_LOG. 1. In a for loop, char string that has changed is not printed out as what it contains now, it is printed out as what...
Hi,
i have purchased the following module
However, after connecting the VCC and GND to 3.3v DC supply the module is not detected. My questions are :-
Does...
how to slove it
1> Linking light_switch_proxy_server_nrf52832_xxAA_s132_6.0.0.elf 1> build/light_switch_proxy_server_nrf52832_xxAA_s132_6.0.0_Debug/obj/ses_nrf52840_Vectors...
I am using the nRF52832.
I want to go to sleep in absolute lowest power mode possible that still allows a timer for wakeup. Using LFINT.
I don't need ram retension, etc...
