Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
Hello,
I am using NRF52832 boars s132 and sdk is 13.1. I have developed my application is read analog accelerometer valie and send to mobile apps. Now i want to also battery...
I'm facing one issue while uploading firmware using BLE DFU.
Details:-
Hardware : NRF52840-DK
SDK : v15.0.0_a53641a
IDE : Segger Embedded Studio v3.40
Mobile App...
We have a Сustom BLE device and observe inconsistent behavior when connecting from this device to to nrf52dk running different SDK versions. - Custom Device connects OK with...
Hi All,
I'm trying to use the nrf52832 as the SPI master to get sensor reading through spi from another sensor. I want to base my firmware on the spi_pca10040 example but...
How can i sample nrf52 own input voltage to do battery measurements?My nrf52 chip is directly connected to a battery and it needs to sample its own input voltage without a...
I have been searching through the info center and can only find the slightest mention of the bsp_board functions.
Could someone help me, locate the right page documenting...
hi sir
i have start my project in NRF52-DK development kit but some BLE card give me data in three channel and i have received all data and give me same like data pls find...
I'm new to use nordic. I am using thingy 52. I would like to add a new custom feature that communicate text via BLE from app, store the text as userid in the thingy and check...
i use 52840, nRF5_SDK_15.0.0_a53641a\examples\peripheral\usbd_msc this example, and change the log level to debug
but i still can not see the DEBUG output information, this...
Hello.
I developing drone by nrf52832.
Developed based on nrf52-quadcopter .
physical web & drone is service uuid as below.
#define BLE_UUID_NUS_TX_CHARACTERISTIC...
Hello, I'd like to connect the nRF52840 to four I2C sensors. These sesnors may or may not have the same address and they will all be at the end of their own 2 meter long cables...
Recently, the side-channel attack "Screaming Channel" was described in a paper ( http://s3.eurecom.fr/tools/screaming_channels/ ).
The authors demonstrate a remote, passive...
Hello Nordic team
I am working on nRF52832 DK and SDKv-11. Can we increase MTU size to send more than 20 bytes in one packet? If yes then any example code do that?
Is...
i use SDK11.0 in 51822, I just need use BSP_BUTTON_1 interrupt, don't need BSP_BUTTON_0 interrupt, but i must initial BSP_BUTTON_0 interrupt, otherwise the current will be...
