I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hi Nordic Tech support team,
I have some questions about nrf51822 dfu OTA.
Nrf51822 application code can't be more than 144K，however ，my application code have 196K because...
we follow the nRF51_Series_Reference_manual v3.0, set the master SPI clock to 8M. but found when in mode 0, the MOSI change near at SCLK rise edge, not in fall edge.
our...
This should have been a very simple question. I don't want to use CTS/RTS flow control signals with my UART-USB-converter ("FTDI chip"). For that case, the document says ...
I want to highlight some items in RTT Viewer
So I tried the color control, but didn't work
This is my code.
SEGGER_RTT_printf(0, "%s[Mutex error:%u]\n%s", RTT_CTRL_BG_BRIGHT_RED...
Hello.
I am trying to port BLE serialization code to a host MCU, to say STM32F4.
I am looking through porting documentation (BTW, it is quite well documented. Well done...
According to Microsoft's instruction on HID touch device, msdn.microsoft.com/.../dn672271(v=vs.85).aspx , a HID touch device should create a report (descriptor) as below,...
Hi,
I am having a 324 byte,a 420 bytes of array stored in flash,now i am updating these array with 360 bytes. in fds_event_handler in the case FDS_EVT_WRITE i am reading...
Hi,
I'm looking for an example which combines FreeRTOS, BLE and ADC on nrf52 board(10040).
I'm able to have FreeRTOS with BLE, FreeRTOS with ADC but not everything together...
Hi,
I've read a lot of question on the forum, but I'm a lit bit confused about what I have to do to use one static passkey on the central and peripherical device. In my...
Hi There,
I'm having problems with my hardware timer appearing to stop counting or not being cleared via a short when the timer interrupt is executing.
In my application...
Hey!
I want to use the nrf51 BLE-module in some special environment.
It should be able to work with bluetooth and in addition to it with some other RF protocol (Gazell...
Hi,
I have added "DFU" functionality to my existing BLE application Test.rar .
"I am using nrf52 SDK v11.0".
I have programmed the device with softdevices (S132.hex...
Hi,
I am new to eclipse on windows.
I have bought the PCA10040 board.
I have installed eclipse and GNU ARM Eclipse 3.1.1 plug-ins.
Copied the NRF52-SDK into workspace...
