How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hi
i am using the sdk 14.0
i am working with sph0645 i2s microphone , i have tested the microphone and it is working fine with the nrf 52 on 912600 baud rate. Now i wan...
Next week, we have a meeting with our customer to give them an overview on all our BLE solutions (they are interested in module) but I also want to give them an overview on...
nrf52832, SDK 15.0.0
I develop the project based on the example 'ble_app_buttonless_dfu'
But when I want to add some peripherals, such as SAADC, SPI and PPI, and some...
I'm seeing strange corruption in the nrf52840 virtual COM/UART (the one that goes through USB and the JLink interface MCU).
The nrf52840 is running the UART serialization...
I had setup nRF sniffer with below software and hardware, but the Wireshark seen unable capture BLE data.
nRF Sniffer software nrf_sniffer_2.0.0-beta-1_51296aa.zip ...
I would like to use the time library to manage multiple times with different timezones in my embedded system.
I have already seen the ble_app_cts_c example and the nrf5...
this is vishal from VVDN tech working as a Hardware design engineer .
In our project we are going to use 10k module of LTE EC25E.
So we need step file from your side ...
Hello,
In ble_app_blinky code,I cant understand this line "#define APP_BLE_OBSERVER_PRIO 3" and what does the value 3 represents here??. Is this value constant or can be...
Hi,
We have been developing our system around nRF52840 and we are now looking closer into the real-time performance of the MCU & SDK. The scenario is simple: a signal ‘YELLOW...
I am trying to add the valid range descriptor to my measurement interval characteristic in the Health Thermometer. This is a necessary step as my measurement interval characteristic...
Hi
I am using the ble_app_blinky's lbs application, as found here in the 14.2 service
C:\Eran\Software\Nordic\Packages\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a...
Hello,
We have an application on Iphone running with our custom service :
uuid : 0000fdF9-0000-1000-8000-00805f9b34fb
and our characteristics :
char-handle 0x16...
Dear Sir, we are developing an application on the nRF52840 kit with SDK 15.0.0. We are using Keil as compiler. In our application we need to receive data from two uart together...
Hi Everyone,
I have two task in which i am receving data from bluetooth and if i receive a particular hex value , i want a task(which is Toggling LED State) to run on...
