Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi,
I would like to check battery level using the SAADC of the nrf52840.
Assuming the voltage is less than 3.6V, do I need to have a resistor between the battery and the...
HI,
I am new to IoS development with NRF.
I am having NRF52840 DK, IoS device. I want to implement USB HID device application (similar to pulse/Gluco meter ) on IOS. I...
Hi,
I am not able to compile the SDK example by using SES for ARM V3.52.
I got one error which shown below:
It pointed to the link ldr r0, =%4
Thanks
Gan
Hi,
I am using fatfs of nRF5_SDK_15.0.0_a53641a.
I am writing a program with keil.
I am currently doing SPI communication with BLENanov2(nRF52832) and SD card with...
Hi,
I am implementing the UART on NRF52840. TX works but the RX doesnot. While debugging, I noticed that STARTRX task register is not getting set due to which the RXDRDY...
Hi Sir
We'd want to do RX testing with DTM mode, however, the dtm example code looks can't report receive data or total packets counts,
So that, we don't know how to determine...
Hello,
I'm using the nrf15822 chip and am using the ble_app_uart example from nrf5_sdk_12.2.0.
I know softdevice will automatically generate random numbers through RNG...
I've been told due to PAN 58 it is not possible to use EASY DMA with nrf52832 without switching to the deprecated SPI driver. Is there a workaround that allows the use of...
Hello,
We are going start custom PCB design by using nRF52840 chip and SDK 15.0, but confused for use 3rd party nRF52840 modules or design complete custom PCB using componenets...
Hi,
Despite knowing a fair bit of the theory of wireless comms (mainly PHY and MAC), I'm brand new to actual hardware configuration/protocol development, so please be gentle...
As a master device with a whitelist there is a limitation on how many slave devices can be connected. If i am correct, other than whitelist there is no restriction to the...
Hi,
How do I receive data from host (computer) on my BLE device(Nordic board)? I want to use a simple open source HID API to send data to Nordic board and glow an led or...
Hello, we have finished all prototyping with BLE modile from Taiyu Tuden, this module: https://www.yuden.co.jp/wireless_module/document/datareport2/en/TY_BLE_EYSGJNZ_DataReport_V1_9_20180530E...
Good day, I am new to this forum so I am having some problems posting my question. Sorry for any inconveniences. I am having serious problems flashing my custom NRF5282 board...
