Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Is there any NRF51822 DFU guide under following conditions:
a. NRF51822
b. SDK11.0.0
c. Dual Bank BLE DFU(\examples\dfu\bootloader\pca10028\dual_bank_ble_s130\)
I...
Hello i am working with light switch proxy client server sdk example.i make provision light and switch using nrf mesh application.i have three nrf52832 dk board.i flashed...
Hi.
I work with PCA10040 and SKD_14.2.
I use UARTE with easy DMA. I see big enough delay between sending nrf_drv_uart_rx_abort and entering to UART event hanler. What...
I tried to create a descriptor for a characteristic. I modified the app_blinky and added a ble_add_descr_params_t variable. After The Initialisation and definition of the...
Hi,
I've tried blink,hid,uart,template similar sdk examples so far. Now i acquired some experience about nrf52832 processor and bluetooth,but ii don't really have enough...
I have had an issue recently with some beacons that I am using to log temperature data. A portion of the beacons drained their batteries very quickly and didn't respond to...
Hi I have this piece of code which works in SDK 12 but when I port it to SDK 15 the sd_ble_gatts_characteristic_add function would fail with an error code of 7. No change...
Hi,
I want to put my nrf52832 into the low-power mode. I select SYSTEM ON with low-power (instead of SYSTEM OFF) in order to overcome reset. In order to do it I call sd_app_evt_wait...
Dear nordic team
I am using SEGGER EMBEDDED STUDIO and nrf52840 DK. I want to add some pwm nrf_drivers like nrf_nvic.c , nrf_soc.c , nrfx_pwm.c to my project. when i added...
Hello,
I started off with two nRF52832 Dev Kits, and have customized the UART Central - Peripheral example to send an array data from Peripheral to Central (no uart simulation...
A month ago I bought an nRF52840 DK to start creating my own projects with the nRF52840 chip
I have created a new project in Segger Embedded Studio for the nRF52840 DK....
Hi,
is it possible to use the nRF52 dev kit and/or the nRF52 Dongle (nRF52840 Dongle) wiith the dongle firmware without nRFConnect?
Background:
We want to use a nRF52...
AIM: Try ATT MTU Throughput Example on nRF52810 running on S132 v5.1.0
Reason: Cant use S112 on nRF52810 because of data length extension. Max speed achievable is 330 Kbps...
Hi,
I have nRF52832 connected to a device(A) which can operate from 3.3V to 5V supply.
When the device's supply is 3.3V, it communicates with nRF52832.
Before the device...
