Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
HELLO SIR
we are working on our current project on bluetooth , we are trying to broadcast message via one nrf52 DK to other nrf52 DKs . i tried implementing the uart example...
Dear Sir,
I am trying to use a whitelist on peripheral side so as to connect the peripheral to a given phone/App.
At first I enabled the "p_advertising->adv_params.scan_req_notification...
I am requesting a USB booloader hex file or if possible the complete project. I have been doing some hacks on mine and have erased the USB booloader. A quick search through...
We are working on the BLE Smart Switch. The requirements are pretty generic:
Low Power consumption
To be used by multiple smartphones within the house
The obvious...
Hi,
I want to set the TX power in a mesh proxy configuration. I have read mesh sdk2.1.1 TX power of nrf52832 , which works good for not proxy situation (e.g for light_switch_client...
Hi, I'm having troubles adding PWM in light_switch_proxy_server example in Mesh SDK v. 2.1.1.
It seems that the PWM driver and instances are not correctly enabled, looking...
Hello,
I was wondering if there are any article or tutorial I can follow to optimize code build with Segger Embedded Studio.
I was able to follow this article( https...
I need logging in almost anything I do, but I've never been able to start from an example that does not use logging and add logging. I've set the NRF_LOG_ENABLED and NRF_LOG_BACKEND_SERIAL_USES_UART...
Hi,
I am using nRF5 SDK 12.1.0.
I have read the s132_nrf52_3.0.0_migration-document.pdf and I am trying to implement the whitelist without the private addresses i.e...
Hello Everyone need your help.
I am using three nRF52840 dongles and have flashed hex file of an nRF example (Ble_Blinky). i want to know whether the hex file is really...
Hi, I am using SDK 15.0.0 and FreeRTOS 8.2.1 (from SDK 14.2.0).
I consistently get a stack overflow on the Idle task, caused by PendSVHandler in port.c
This can be easily...
Hi,
I'm using nRF52832 on nRF52 SDK v15.0 with S132v6.0. I know that 52832 support high throughput and advertising extension. We have more than 31 bytes data to put in the...
Hi,
I have created up to 5 custom services with several characteristics (4 at maximum) each one. They all use the same base UUID.
The problem I'm facing now is that when...
I am adding CLI service with my existing project developed based on ble_app_uart.
CLI Init function :
static void _cli_init(void) { ret_code_t ret;
#if CLI_OVER_UART...
