We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi,
I'd like to be able to use an event from the LPCOMP to sample the RTC (either to a peripheral's register, or to a memory address), so I can measure pulse widths without...
Hi there!
I am running the Thread Border Router example and have successfully loaded RaspPi_OT_Border_Router_Demo_v1.0.0-1.alpha.img into the RaspberryPi 3B+.
The problem...
Hi,
I've modified light switch client to read input from GPIO pins . I used int_pin_change as a reference for initializing inputs. The Int_change_pin example uses interrupts...
Hello, I'm developing an debugging an BLE application. I'm using nRF Sniffer (dongle) N51422 PCA10031. I can successfully sniff and decrypt ble secured connections of my application...
Hi all, I want to add light switch client to light switch proxy server . But I dont know how to get appkey handle for bind to light switch client . Pls , help me !! Thank...
Hello,
I'm unable to capture packets using the sniffer. Here are details regarding my set-up:
System: Debian 9.4 with kernel 4.9.0-4-amd64 #1 SMP Debian 4.9.65-3 (2017...
Many of the pins in the assignments page of the documentation are designated as "Standard drive, low frequency only" and I cannot seem to find an explanation of what is considered...
I am trying to connect my android mobile with nRF 52DK using BLE on the NRF TOOLBOX android application. But the nRF 52DK is not recognize by the NRF TOOLBOX APP(proximity...
Hello,
we have a problem using the SAADC module with the low power mode, particularly after execution of the NRF_SAADC->TASKS_SAMPLE task.
Before taking a sample, the...
Hello,
I have some questions about ble_conn_params.c in SDK14.2
Question :
1. a. Why do you need to handle four ble conditions ?
b. Shouldn't just send connect parameters...
I hope to use a acceleration sensor with nRF51822 dev kit. So I should use three ADC input. I tested getting one ADC data using adc_simple example(Keil_v5/ARM/Pack/NordicSemiconductor...
We use nRF52832 ,when new android phone will connect to this device by mac,we cannot connect to it successfully,we must scan to find the device first,after found it,we can...
I want to t o ensure the stability of BLE connection for BLE frequence calibration,but i don't know how to get the nordic into the test mode and broadcast the empty packet...
https://devzone.nordicsemi.com/f/nordic-q-a/9231/ble_hci_conn_failed_to_be_established-0x3e-problem/34074#34074
I also encountered the same problem as this one. How to solve...
