After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Chapter "18.6.1 Power-on reset" of the data sheet describes " A step increase in supply voltage of 300 mV or more, with rise time of 300 ms or less, within the valid supply...
Hi,
I'm using the BDS Plugin to generate code and I noticed that the code generated for adopted services it's totally different compared to the code into nRF5_SDK_14.2.0_17b948a...
I am trying to use the watchdog interrupt on an NRF52832 but am unable to get it to fire; the watchdog fires, but as far as I can tell not the preceding interrupt. Here is...
Hi,
Does nrfsniffer require a separate dongle? Can I only use my Nordic board with USB cable, sniffer tools & Windows machine? Will that suffice? Well it lists that way...
Does the nrf Mesh Android App/iOS supports Extended Packet Length? Like MTU size > 23 .
I have used Samsung Galaxy 8 but I am not able to provision the Device , even though...
Hello,
I want to use ANT+ communication on the nRF51-dongle that has a PCA10031. I have downloaded the SDK 12.3 to use. I have used some of the BLE examples before that...
Hi all, in new update app NRF Mesh Android, I can send data from Android app to Kit run light switch proxy server in SDK MESH V2.2. But It using generic_on_off_server. So...
My setup is a Android phone, Nordic NRF52, and random BLE devices in the area.
What I want is, the Android NRF-UART app connects to the NRF52 and the NRF52 sends information...
Hi,
i use the Aead-Lib for CCM on the NRF52840. What is the best way to Check an Mac from a Message wich only has Adata (no acctual encryptet message)?
If i try to use...
Hi,
related to a previous question I posted, , we are migrating from nRF5_SDK_13.1.0_7ca7556 to nRF5_SDK_14.2.0_17b948a.
Now we have some problems with the bootloader...
The subject really says it all; why are there four GPIOs tied to P0.18 which is the nRF52840's RESET# pin?
I'm looking at the PCA10059 Schematic available in the nRF52840...
I am currently using the nRF24L01P in an application where I am using the RPD feature to determine whether a 2MHz RF channel is "available". For example, if a wifi network...
I am using nrf52832 and I am trying to interface OLED with it. I am attaching the code below and i referred that code from https://github.com/devdprj/olednrf here,
i made...
Hi All.
I have a DK52 project where a peripheral advertises and connects to a central nRF52840 ok. I based it on the multilink_central demo, so have the LED button service...
