Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hello,
I am trying to port the light switch server example form the nRFSDK for Mesh to IAR Embedded Workbench for ARM.
I am using
nrf SDK Version 15.0.0
SDK for Mesh...
Problem : bytes are lost during UART communication with the module, hardware flow control is enabled, at speed higher than 38400 baud/s, when softdevice enabled and test board...
Dear Nordic
I have facing some issues in RTC side. In my application RTC and BLE works same time . First installation and set time using function nrf_cal_set_time() works...
Hi all,
I want save and read flash in example light switch proxy server .
I add code part of provisioner example into proxy server example
This is my code ;
And...
Hi everybody,
I have a question about the nrf52832 how to set the tx power in the ble peripheral uart example. i want to set both the advertising tx power and the after...
Hi,
I'm testing BLE Central multilink base on nRF5_SDK_15.0.0_a53641a\examples\ble_central\ble_app_multilink_central\pca10040\s132\arm5_no_packs
With modification in main...
Hello all !
I've been searching for an answer to my problem over the forum but I haven't found exactly what i'm looking for, so, that's why i'm posting this.
I'm using...
Compiled my first blinky example for pca10040 nRF52DK, nRF52\nRF5_SDK_15.0.0_a53641a, Keil mdk5, W10. trying to download compiled code got the error: The firmware of the connected...
I want to save Power by disabling the SD Card. VCC of the card is already regulated with an external MOSFET switch and controlled by a pin of the nRF. The problem now is,...
Hi,
I'm currently using SDK 14.2 (on 840) and SDK 15.0 (on 810) with the UART example.
I'm trying to implement the following system.
The Device only receives data...
Hi all,
I'm using SDK 15, nrf 52840, win 7,
The USB cdc example works fine for me.
Yet, when I moved the code to my project the driver is not set by win 7.
On device...
hi Support Team
I am working on Asset Tracking project.Looks like Bluetooth Mesh is more oriented towards controlling.
I have a Ble device Emitting some Data. (say A)...
Hello there,
I have developed simple coap client and simple coap server based firmwares on nRF52840. My hardware/software configuration is:
SDK: nRF5_SDK_for_Thread_v0...
Dev Env
- SDK: v12.1, SoftDevice : S132 v3.0.0
- NRF52 start program : ble_app_uart_c
1. Is it possible to connect to NRF52832(Central Mode) from Android(Phone Pheripheral...
