Hello! The PCN 219 rev 1.1 says "The new device revision of nRF54L15-CAAA is not drop-in compatible with the current revision, requiring update to PCB schematic
and layout...
Hello.
Im tring use nrf_dm sample with nRF5340 on nRF Connect SDK V2.9.0, with a custom board.
I got the error when I try dm with other device:
my prj.conf:
...
Hi, I'm currently in architecture definition stage, and I'd like to know more about the possibilities driven by Channel Sounding. From what I understand, you can only perform...
Hi,
I am encountering an issue with the TWIM driver when attempting to communicate with the nPM1300 PMIC via I2C.
This problem seems to be related to the behavior of the...
I have been trying to implement a way to wake the system up after doing sys_poweroff() but no matter what nothing seems to work. I already tried many examples and none of...
Hello,
I have been able to get FW OTA to work perfectly well over BLE using
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
Now I am trying to display the update progress...
The custom AT command "AT%XICCID" was added in modem firmware v1.1.3 for the nRF9160 and was available from the first release for the nRF91x1.
This command provides a processed...
I know there have been many posts on this forum regarding a similar issue, I have spent a whole day reading them and trying to get this working, to no avail.
Basically my...
After nRF52840DK is flashed with open bootloader project through J-link ( usb port J2 on the short side of the board), nRF connect is showing the following interface when...
After reviewing this thread https://devzone.nordicsemi.com/f/nordic-q-a/53743/zigbee-sdk-on-top-of-freertos I managed to get FreeRTOS working with ZigBee and BLE using the...
On the development boards, the JLink OB stops working after 24 days and needs to be disconnected to work again.
This affects at least the USB UART endpoint, but possible...
I have seen some situations where putting the modem into offline mode (CFUN=4) will cause my application to lock up because the at_cmd never returns. It looks like this is...
Hi, I am using Mesh SDK 4.0.0 and have couple of nRF52840 dev kits.
1) In light switch server example of Mesh SDK, is it possible to add more on_off data types to the server...
Hello I am trying to develop an application for advertising in SLOW mode.
Here is my Advertising Init function.
/**@brief Function for initializing the Advertising...
Can somebody help me out the reason behind below failure on thingy 91. I am building asset tracker example using west on command line. Following is the logs that i got after...
Hi,
I am working on the Thingy91 and trying to set up an event when the USB power state changes (USB cable w/power is plugged or unplugged). For now I will just blink...
Hi,
I changed the softdevice on the nRF52833 light client example from the S113 to the S140, but the program
hangs at startup before even enter the main loop (catched...
Hi ,
During the review, I came across the certification question. After some reading, I found some details.
This got me worried because it looks like it is a difficult...
I have found the example using nRF52833 in the latest SDK (ble_app_att_mtu_through....)
I am using Keil uVision 5.29.0 and I have downloaded the software packs 8.27.1, 8...
Hii,
Our input voltage to nrf52840 is 2 volt, we want to know whether 2 volt will be detected has low(0) or high(1) or undetermined state.we are using gpio pins (1,10) and...
Hello,
I'm considering writing BLE relay application, where central side should bond and encrypt connections (cause sensor device requires it and will not function without...
I'm trying to get the most performance per mA out of my nRF52, for test purposes I've used the nrfx libraries to communicate to the peripherals but I want to make my own....
