Hi.
We are doing automatic network attaching on nRF9151. This is how the flow looks:
AT%XBANDLOCK=2,...
AT+CFUN=1
AT+COPS=0
We do this until we get registered...
Dear Nordic Engineers
We found a problem on the NRF54H20. When we ran C:\ncs\v3.0.2\nrf\tests\benchmarks\multicore\idle_gpio example, the current tested on the VDDHV of...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hello team,
I am using nrf54l15 dk for the devlopment and want to read the RTC counter to check for how much time my device was in sleep mode.
How to achive this?
Thanks...
Hello, I'm using nrf9151-DK kit and this UDP example: UDP . After compile and flashing I opened both serial monitors (VCOM0, VCOM1) but no output appeared. Could you please...
Does single bank bootloader in SDK7.1 support ZIP-file ?
I get error REMOTE DFU INVALID CRC ERROR in the end of flashing by nRF Toolbox when I use ZIP.
If I use hex-file...
Hello,
I am trying to implement OTA firmware update using Secure DFU.
SDK - 12.2
Softdevice - s132
Board - PCA10040 (nRF52)
I followed instructions mentioned...
Hello,
I just want to clarity the sd_ecb_block_encrypt() operation cases (S110).
In pp. 23.1.3 of RM (Shared resources) sayed:
The ECB, CCM, and AAR share the same...
Assuming SDK 12.x
For those people that want to integrate the Buttonless DFU service to their app, which uses already one custom base 128bit UUID, please make sure to:...
I need to add connectable beacon advertising data instead of normal advertising for proximity profile example (NRF52 DK -> PCA10040 ->S132 -> nrf52832).During Advertisement...
Hi,
We had a power issue with our custom board related to DFU updates. After performing a DFU we were seeing 8mA idle current, and when we had programmed the firmware directly...
Hello,
can you provide a best practice guide on how to use memory protection unit in nRF52832.
I am interested to know if MPU can protect user defined memory regions...
Hi,
I want to know Tx power and duty cycle information of Beacon and NRF52 for the following cases:
In our case NRF52 will be our receiver and Beacon will be transmitter...
During the CE immunity test, the nRF51822 has to re-connect automatically without user interaction when the BLE connection is blocken by noise. Please tell me how to implement...
hi,all
my device use CR2450 button battery,advertise time 500ms
TX POWER:4dbm,the battery life is low if it still use this configuration
(May be big current lead...
Hi all,
I am using a nRF52832 with SD S132 V4.0.2 ion SDK13.
My application currently uses TWI, SPI and BLE and also 1 wire (which is based on delays). Everything works...
Hi!
I am working with PCA10040 (nRF52), s132 and SDK 12.2.0.
I am using the example experimental_ble_app_eddystone.
I have configured one slot as TLM, so it reports...
Hello,
We're using JLinkExe for production programming. Is there an equivalent of the nrfjprog --erasepage command for JLinkExe?
I'm looking for the equivalent of
nrfjprog...
Hello,
I feel like this question has an answer similar to this question, but I can't seem to get it working devzone.nordicsemi.com/.../
I am using the nrf51422 chip...
