Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hello,
I've been using UART DFU feature quite extensively in one project which caused that I had to stick to SDK11 features (since bootloader relied on SD 132 2.0.0). ...
I couldn't see this in the documentation, but I might have missed it. Does the Logger Module consume additional power when it is enabled/initialised? If it does, presumably...
Hello,
I have developed a board with the integrated nRF51422 QFAA. I have the nRF51DK.
To compile I have used both mbed and arm-gcc and the binaries work perfectly on...
Hi everybody.
I am making a firmware based on ble_app_uart example (PCA10028 NRF51422, Softdevice S110, NRF51 SDK9.0). In this firmware, I insert dfu part ( follow by this...
I am testing out the Bluetooth Mesh SDK 0.9.1 Alpha using the light control client/server example. The examples have not been modified.
I have set up a nRF52 development...
In android while at the stage of scanning there is list of ssid ,i am getting print of scan_result but while trying to print the RSSI value,the result is 0 .Files i have changes...
With our custom board, I have implemented the battery service and it's working well. But the nus service is not shown up at all, the same initialization code as the official...
i use the nrf52832,s uarte. using the app_uart_fifo.c document. but i can only receive the max 256 bytes.the configuration is belows:
APP_UART_FIFO_INIT(&comm_params,
...
Hello,
Is the characteristic value data supplied to sd_ble_gatts_characteristic_add() and sd_ble_gatts_value_set() copied into the softdevice RAM, or does the softdevice...
.pdf d051cefddbc197cd7d)
Hello All,
I am working on Automotive project using nrf51824 SOC...
Hi,
I am working on making a test harness using the nRF52DK and a raspberry pi so I may run unit tests directly on the nRF52832. I want to use the UART to give test results...
We recently did pre-compliance RF radiated immunity testing at a certified lab. The EUT was nRF52832 on a battery powered post card sized circuit board with some sensors....
when I run the program I get this error
Checking installed packages
pyside: 1.2.2
pyqtgraph: 0.10.0
numpy: 1.11.3
pynrfjprog: 9.1.0
Warning: The software is tested...
I am using a PPK with v1.0.0, but elsewhere in DevZone I see references to later versions of the software. Where can I download the later versions from? Have I missed a link...