Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi I use 4 characteristics in peripheral and central. When I write to one of the characteristics in the peripheral, I read it using sd_ble_gattc_read in the central. But,...
Hi,
SDK14.0
nRF52832
I am using the dfu\bootloader_secure_ble example as my starting point. My goal is to create a very simple bootloader (with none of the dfu stuff...
Hi
We are trying to use the uECC library file (micro_ecc_lib_nrf52.lib) with our project that is built in Kiel. We have followed the instructions found here using the open...
Hello,
I'm using SDK 132 (v5), kiel 5, SDK 14 and the nrf52 dev board.
I'd like my application to have multiple Offical Services (Heart rate, Humain temperature,...
Hi,
For my new project, I copied the linker script and Makefile from examples/ble_peripheral/ble_app_uart/pca10040/s132/armgcc to a folder and changed the SDK dir and project...
Hi All,
I have developed a device using the nRF51822, and the connection interval is set to ~1000ms.
When reading a characteristic from a Raspberry Pi, we are timing...
Any updates on this from anyone? Please advise
Hi,
The i2S microphone that I am using requires a over sampling rate fixed at 64 therefore the WS signal (LRCLK on nrf52...
Hi community, I'm running a 51802 on my custom board with no other parts on it, except for some buttons and leds directly connected to GPIO, and a DC/DC converter which feed...
The term 'slot' is used in the context of the Eddystone beacon specification.
I cannot find a definition of that word.
For example, the sample app from Nordic says ...
I set up an account a few days ago on nordicsemi.com and today it's rejecting my login. I then requested a new password which was sent to my email but when I copy and paste...
I am studying how to update the firmware through BLE at the moment. I used the example project of "ble_app_buttonless_dfu", but I am having many questions that I don't understand...
Hello everyone,
My job is to migrate a functionnal code made with IAR to GCC Eclipse.
When I compile with IAR and flash the hex file (softdevice and application) using...
I'm using:
bootloader_secure example in SDK 12.3.0
SoftDevice S130 nrf51 2.0.1
Is a bootloader update 100% failsafe against power loss anytime during the process...
Hi:
I am using nrf52832 and I met a strange problem:
SDK version: nRF5_SDK_12.2.0_f012efa
First experiment(NO BLE):
using example peripheral/timer:
code...
Hello Everyone, I want to use NFC on nrf52 DK to wake up the board from System off. Is there any examples similar to this situation where I can learn more about NFC and Sense...
