It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
what is the sending data rate of the sd_ble_gatts_hvx() ,why i use sd_ble_gatts_hvx() send data 600Byte per second, it lost data again . it can be use yes or no ?????????...
I can copy a Hex file from a Mac to the mbed USB drive and the code executes correctly. However, if I upload the hex file from any windows PC in our office (Windows 10) the...
Hello, I am trying to generate pulses with the nRF52832 chip.I created a basic setup for test purposes; I simply connected a LED to the PWM output, but even though I put 0...
Hi,
I have designed the Circuit using NRF52832 BLE and AT8010-E2R9HAA RF ANTENNA and tuned the circuit accordingly. Since the antenna was not available so I placed other...
I'm relatively new to development on the nRF52832 and I'm trying to find information on how to use the sleep mode with the SAADC.
Goal: The micro should be in sleep mode...
Hi,
I am trying to create a BLE node which can perform dual role(advertising/scanning) to create mesh of multiple nodes. I am planning to do it with the help of timer....
the project has a problem with DMA,the detail is:
on the board,NRF52832 and extern chip communication with i2c bus,the chip through a pulse wake up nrf52832,NRF52832 start...
I have NRF51822 Controller(custom board,S110) used to send some sensor data. i can able to receive data in android and ios. now i want to communicate to Laptop which has internal...
Hello Everyone,
I am new to nrf51822 (using S130). I made some custom service that accepts float numbers.
This might be noob question: I want to send float values from...
We are developing a custom ble service and profile however having printf makes our lives that much easier so we are trying to incorporate it purely for testing purposes. ...
Hello,
I'm trying to optimize my application :
I have a central (nRF52832 s132) which communicates for a short time to a peripheral (nRF51822 s130) and then disconnect...
Hi
I'm trying to register an fds_evt_handler() in SDK 14. I have several questions:
Should I be registering fds_evt_handler() with NRF_SDH_SOC_OBSERVER or NRF_SDH_BLE_OBSERVER...
Hi!
Is there any chance to get the Altium files for the nRF24L01 refmodule with PCB antenna? I found the files but for the SMA version and I'm trying figure out the same...
Hello,
This is Milav Soni from Teq Diligent,India.
I explore the nRF52 series Chip and nRF51 series chip.
I also explore some of your BLE video.
I have one question...
Hello,
I'm using SDK 13.0.0.1 to develop my project. For driver example, such as RTC, I can't see data log while I can see the data log for BLE example, such as ble_app_uart...