Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
I’ve got a bit of a hardware issue with the nRF52811 UART, receiving DMX data from a Chinese DMX controller.
Standard DMX data-rate is 250Kb/S, so the minimum bit time is...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
I have an application based on the ble_HID_keyboard_template (uses STM32F072 instead of Arduino). The first time I pair my iPhone 5 (iOS 8.1.1) with the nRF8001, everything...
Hi,
I'm using nRF51422 with S310 and ble_app_hrs example application.
Thus I can simulate a Heart Rate Sensor with the board and get data on an Android phone with the...
Hi all! May I use another quartz instead of 16 MHz? Will the output frequency equal to 2.4GHz/16, if I will be use the 1 MHz quartz? Or IC will not work? Is it possible to...
I need to evaluate the real consumption of current for BLE events on RF81822. The HFCLK is 16MHz and the 32kHz clock is external.
S110 Soft Device Specification V1.2 document...
Hi, I am using S120 1.0.0 and SDK 6.0.0. Learning the sample project 'ble_app_multilink_central'.
I already got a peripheral device with NUS service. The central device...
I am new to this great platform and am struggling with getting my PIR sensor connected to my DK. I wonder if some of you experts could give me some pointers on how to go about...
Hello, I build a BLE 6LoWPAN environment on my raspberry pi with Kernel 3.18.3 and connect a BLE Dongle. The BLE Node is Arch BLE ( www.seeedstudio.com/.../Arch-BLE-p-1998...
Hi, I have two different types of nRF24L01+ modules, both behave differently.
The "troublesome" module always has TX_DS asserted after a transmit, which is the same behavior...
Hi,
I am using the SPI Master 1 to control an EEPROM. I used the spi_example project to help get the code working. It all works fine if the code that initiates the SPI...
We have designed a differential antenna for the nRF51822 CEAA chip.
Each of the RF output connects through a matching circuit to each one of the two 50-ohm to ground end...
How to setup MQTT for CloudMQTT? I have working raspberry PI I can ping and connect to device when follow the user guide. Now I like to try MQTT example but don´t know how...
Is there a list of every interrupt these functions effect. Specifically I am worried about
static void ble_evt_dispatch(ble_evt_t * p_ble_evt)
My assumption is that...
Is there any S110 demo with good communication between periphera and APP in phone side in SDK 6.0? It means that data channle works well from 51822 to APP and APP to 51822...
Is there any S110 demo with good communication between periphera and APP in phone side in SDK 6.0? It means that data channle works well from 51822 to APP and APP to 51822...
The nRF51 series reference manual v3.0 documents 3 Real Time Counters: RTC0, RTC1 and RTC2 (pp 17 and 109). However, RTC2 does not appear in the SDK documentation (e.g. no...
