Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi, I just flashed the BLE_proximity example in the ...\nrf51_sdk_v6_1_0_b2ec2e6\nrf51822\Board\nrf6310\s110\ble_app_proximity in the nRF51822 Development Kit, and the nFR...
I am working on a custom BLE service on the PCA10001. I can successfully detect and communicate with the PCA10001 using windows x64 MCP. I can also detect and communicate...
Dear Sirs
I am new with Nordic BLE Modules.
After successuful pairing with Windows 8.1 in a Tablet I need to get an active Service. For example I would like to obtain Battery...
We have an NRF51822 running S120 at 32MHz.
Our system has two removable batteries. If a battery is removed we need to switch to the other battery as fast as possible. We...
For TWI, SPI and UART is there a significant power savings from powering down the unit when not in use vs just disabling it?
Disabling the unit seems reasonable, but powering...
Hi!
I was trying to use nRFLoader to update firmware using example DFU Bootloader but app hangs on "Discovering" (after selecting device to update). What can be the reason...
Currently I can upload new application firmware smoothly (I use the dual bank setup). However, I have to use packets of size 20, so this takes a long time.
Is there actually...
hai ,
i am using the NRF51822 development kit. The NRF51 dongle i have used as a sniffer and a master control panel. Is it possible to load and run a s130 softdevice and...
Hi, I'm trying to estimate the nRF51422 current when running ANT. Does the softdevice use the RTC (LF oscillator) when in wait mode to save energy? Thanks
The Segger programing interface works. The virtual com port appears on my PC (COM5). The problem is that there is no board listed in the Motherboards section of the Device...
Hello,
currently I try to implement a GATT server on a nrf51422 with the s310 Softdevice. For testing I use the LightBlue IOS client on an ipad. I can see my GATT server...
I am creating an Apps which will give me a list of the running Apps in the background and foreground.
Hence Using XCode, I want to programmatically detect
List of Running...
I have a Arduino board and I want access to Ant Stack by UART. I flashed S210 in my nrf51422.
I try connect the Arduino RX/TX with TX/RX (P0.12 / P0.13), but none. Also...
Hi Nordic,
I'm wondering if I can use IAR Workbench to download SDK for nRF51DK rather than Keil. I want to develop a beacon that uses Bluetooth Smart. Can I do that in...
Hi,
Does the .hex file for V7.1.0 include the master boot record? I'm writing a JLink script to flash it and I'm trying to figure out, once converted to a binary file,...
