hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice , like this:
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
Hello! I try to add nus service to ble_app_template.
I add ble_nus.c file into project
add include "ble_nus.h"
declared service
BLE_NUS_DEF(m_nus);
add into...
I guess my question is stupid, but I would like to ask it by the way..
in all ble examples we use a function for handling ble events by our app
in my case in example ble_app_uart...
I'm trying to launch my app on a custom board with nrf52 after a successful launching on DK. The problem is here: err_code = sd_softdevice_enable(p_clock_lf_cfg, softdevice_fault_handler...
Hi folks, I'm making progress with a program to get two nRF24L01p modules communicating with each other, but there are a couple of remaining problems. I hope someone can help...
I have a little bit of experience on TI BLE stack development and wanted to move to Nordic product with Bluetooth or ANT protocol for a higher data rate. I got a general question...
Hi All,
I have a problem with .hex file. I use example ble_app_uart from nRF5_SDK.
In examples\ble_peripheral\ble_app_uart\pca10056\s140\armgcc I executed: make all and...
I try to turn off the system with sd_power_system_off()
// Go to system-off mode (this function will not return; wakeup will cause a reset).
err_code = sd_power_system_off...
Based on 'ble_app_template' in nRF5_SDK_12.2.0 (S132), I develop a program with nRF52832.
The problem is that the program will restart after reaching APP_ADV_TIMEOUT_IN_SECONDS...
Hi,
I have a few questions about using floating point in nRF5 chips. As discussed here , nRF51 has no FPU but we can simply use "float" in Keil and have the operations...
My device as a slave, if the surrounding environment is not good, the unknown master device connected to my slave device caused the real master device to be unable to scan...
Dear Nordic family,
I tried programming MDBT40 (purchased from Raytac ) with the same code which worked with nRF51822 Bluetooth Low Energy BLE 4 and 2.4GHz Wireless Communication...
I'm trying to implement a simple RTC timer into my project, and it seems like the app_timer module is the best way to do that, especially when using the Softdevice. I added...
Hello,
we are facing the following issue when using Android and trying to rebond with a previously bonded S110 peripheral:
Bonding the Android device with the S110 based...