Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
We are designing our 2nd pass design based on nRF51822 this would be our production version PCB.
We would like to have our Schematics,Layout and BoM reviewed from your...
Hi,
I am using softdevice-7 and SDK 6.1 for our application. I want to implement static key pairing for serial port over ble application "ble_app_uart".
I have implemented...
I have a 384 byte, writable, variable length, vloc user characteristic and I want to trigger an event when the write completes so my application can operate on the data. ...
Hello-
I am trying to program a custom nRF51822 board with a J-Link-lite.
From the J-Link-lite, I am using the 10-pin header and have it wired like this:
I'm using pins...
I have a situation where I need a software PWM for several channels, which are multiplexed via a shift register.
The output loop needs to run at several kHz for this to...
Because of the limitation in the GPIOTE hardware that only one channel can be connected per GPIO , care must be taken when changing a PWM duty cycle. If for instance the compare...
Links: https://devzone.nordicsemi.com/documentation/nrf51/6.1.0/s110/html/a00081.html#ota_profile_pkt_rcpt_notif
As you see,GAP Disconnection，I don't Know how it works...
Hi Nordic
I do not know why sometimes program can build pass in keil ,but can make nrf51822 do not work and unable download program . For this , I have damaged a lot of...
Does the nrf51822 support 2 spi masters (on different pins)? I want 1 spi channel to talk to one set of peripherals, and the other to talk to another set. I see SPI_MASTER1_ENABLE...
Maybe question similar to this one devzone.nordicsemi.com/.../
Can I use the interrupt generated by RADIO_IRQHandler(void) while implementing another protocol?
At the...
Hi everyone,
for our current project we have to implement some sort of activation lock. Therefore, we would like to use the MITM security mechanism of BLE. The idea is...
I have an nrf51822-mkit.
Let's say there are 2 BLE phones continuously searching for my module. Phone 1 connects and communicates with the module. The modules determines...
I used the ble_app_lbs example as a template, with a PCA10003 eval board (nrf51422 chip). SD 110, Nordic SDK V6.1. Keil uVision 5.
I launch my application and my board...
Hi,
In softDevice S120 can we make second sd_ble_gap_connect on different peer, without waiting confirmation connect of the first one ?
Bests Regards,
Jérôme
