Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hi everyone,
for our current project we have to implement some sort of activation lock. Therefore, we would like to use the MITM security mechanism of BLE. The idea is...
I have an nrf51822-mkit.
Let's say there are 2 BLE phones continuously searching for my module. Phone 1 connects and communicates with the module. The modules determines...
I used the ble_app_lbs example as a template, with a PCA10003 eval board (nrf51422 chip). SD 110, Nordic SDK V6.1. Keil uVision 5.
I launch my application and my board...
Hi,
In softDevice S120 can we make second sd_ble_gap_connect on different peer, without waiting confirmation connect of the first one ?
Bests Regards,
Jérôme
Hi
NRF51822 with SD7, S110.
I have some troubles with DFU procedure. I uploaded standard OTA-DFU bootloader and S110 to my NRF. Everything works well with my code except...
Hi,
I was wondering if it is some easy way to turn off that the system goes into system off mode after a while for ble_app_pwr_profiling?
I would also like to test it...
hello everyone,
we're currently working with some nrf51822 beacons and throughout the project we recorded the antenna patterns of several of them. In the first batch we tested...
Hello.
I neet to write long characteristic value (250B). I use GATTS Queued Writes from example devzone.nordicsemi.com/.../ based on developer.nordicsemi.com/.../a00892...
Hello,
I am frustrated by a pair of nRF24L01+ communicating with each other, where all the Enhanced ShockBurst features are enabled.
The PRX is initialised as follows...
I could scan/detect Beacons, and I could update the configuration without any problem with the nRF Beacons app. The issue is that the configured Beacons are not detected in...
Hi,
I want to use the nRF51 dongle with the Master Control Panel.
I found in the nRF51 Dongle User Guide that the Dongle will run with the Master Emulator firmware, but...
I don't expect the Nordic engineers to know this answer but I'd like to hear from other devs out in BLE land...
Have any of you encountered truly horrible BLE PHY-level...
I am using S120 device to receive advertising from S110 device and need to get the exact time + sender's address information at Radio End Event.
I use PPI to start Timer1...
Hi,
I'v try to use the sd_power_system_off() and without successful.
The power consumption will be 200~230uA around.
My device:
Call the system off when ADV._TIMEOUT...
Hi
I am trying to make a ble central with s120 on a pca10001 board.
My problem is that it sometimes take a lot of time (up to 10 seconds) to find the client when i make...
