Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hi there. I'm Matthew!
I noticed that there were contests sponsored by Nordic in the past, such as
Startup Weekend, June 15-17, 2012
The Nordic Semiconductor App...
I can use nRF Toolbox as a central to test various nRF5 as BLE peripheral samples.
Is there any sample app (iOS or Android) to test the few nRF5 as BLE central samples? ...
Hello.
I am trying to turn off ACK in the example "esb_ptx". I have tried this in both SDK 12.2 and 14.0.
I try to turn off ACK like this:
static nrf_esb_payload_t...
Hi,
I am trying to establish a border router in my test Thread system (a part of infocenter.nordicsemi.com/index.jsp . I have the required Raspberry Pi 3B, but it is driving...
I'm using the 1.0.1 nRF Sniffer and 1.10.10 Wireshark on Windows 10 64bit. The firmware 1.0.1 is programmed to nRF51822 dongle using Jlink 6.12a. The exe works fine when no...
Hello everyone,
I want to integrate NFC to one of my projects and I am having a problem with the value of some of the capacitors.
I am looking into using the nRF52832. ...
Where can I download the example project that can be imported into Eclipse?
Tutorial: devzone.nordicsemi.com/.../
Broken link: ble_app_hrs
When I follow the link...
can't program nrf52832ciaa
I can connect the core through segger commander
I can erase the chip after push the download bottom in the keil 5 ,and erase the chip...
I have an nRF5- DK and I'm following this tutorial . I loaded the softdevice, I can compile, I can load the flash, I can see the output in Termite, I can change the code to...
Hello,
I have an NRF51822 custom board. I am trying to flash the code under
C:\Users\Home\Desktop\nrf51\nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_uart...
Greetings -
The (custom) device I'm working on has multiple possible serial interfaces. I thought "Hey, I've written entire operating systems before, I should just intercept...
Hi all,
i need to write in flash, and i try to use the example flash write of sdk. It works correctly but when i put it in my code, the writing register ( NRF_NVMC->CONFIG...
Hi!
I'm developing Thread mesh using nrf52840 with COAP communication. I would like to set a longer timeout and more retransmission tries in COAP. I saw this parameters in...
I am trying to use one of the example from NRF5 IoT SDK with RPi3 (kernel 4.9.41-v7+) but keep getting "permission denied" when execute command below:
echo "connect 00...
Hello
I have setup my Eclipse(neon3) on Linux following the instructions in devzone.nordicsemi.com/.../7
I cant compile and flash the image. But cant breakpoint.
I...
