I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I am setting up the DFU example to compile in Clion using ARMGCC 4.9 2015q3 and cmake. Everything compiled as it should and the DFU advertises. However, when trying to do...
hello there,
i want to send and receive data using spi and i2c protocol and i am using nrf51422 .how to interface which pins should i use to make spi and i2c communication...
I have an application that toggles an LED on P0.26 based on a timer and that's working fine. Now I need to add a few more timers so I decided to use the APP_TIMER library...
I am having trouble with an application where the NRF52832 operates several devices as a TWI master. What is even stranger is that I have been working on this code for a while...
I am developing a keyboard using the nRF52832 and example code(ble_app_hids_keyboard).
SDK is SDK14.
Korean/English change is not possible.
The specification I refer...
hello there i have basic question about BLE. what is difference between link layer and GAP??
i know about host and controller. but in both layer there is advertisement and...
We are using the NRF52840 as a basis for BLE-based secure IoT network. I know that the Crypto library enables hardware-accelerated encryption/decryption. However, as far as...
Hi guys, I'm trying to nail down this TWI issue. PAN 89 is related to TWI being used in conjunction with the GPIOTE module. However I manually wrote my own application level...
Related to SDK 12.3.
Quoting this question :
GPIOTE PORT event generated on the
rising edge of DETECT signal. Please
have a look at section 15.1.2
2)DETECT...
Hello,
I am experimenting with sending large notifications from an nRF52 configured as BLE peripheral with SoftDevice S132 v5.0.0. I having some trouble receiving the notifications...
Hello guys,
I would like to execute code once a scan request from any other BLE device is received by the NRF52 using Zephyr.
Unfortunately, I am not able to receive...
Hi everybody,
I have an issue with my application, I want to use the ble with the same antenna that it use in the development board PCA10036,
Could you please tell me...
When I send 512 Byte from my Android phone I received only 20 Byte. How I can received more than 20 Byte? I used example project "ble_app_uart", SDK 14, SoftDdevice s132,...
I am working with SDK 14.0 . I see two "type" of advertising_init() function :
1-
static void advertising_init(void)
{
uint32_t err_code;
ble_advertising_init_t...
