Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
I would like to integrate BLE serialization with a nrf52832 and S132 soft device in a STM32 project.
I tried to identify which parts of the heart rate sensor example...
Hello,
I'm trying to flash my nrf52 DK but it's not detected by nrfgo studio.
here are the version of the softwares i'm using :
SDK : 14
JLink : 6.20g
Command...
Hello NorDev. community,
I have two sensors operating on nrf51822. I control them manually by mechanical switches at the moment.
I would like to change this sensor control...
hello everone
1、I tried the thingy52 sound demo ,but quality of the sound is bad, It is because the limit of the transfer speed？
2、I want transfer the sound by ble，how...
I would like to start off by saying I am not a very experienced programmer and I only have base knowledge of Java and Android Studio. Furthermore, I have no experience in...
when I run the secure bootloader example in nrf51422 development board, the code is working fine. I am able to load the packet through nrf toolbox app. But the same code when...
hello
i am using nrf 52840 board with sdk 13.
i use heart rate collector example to connect the 6 heart rate peripheral .
Modified the hrc_c example following this link...
I want to monitor NRF radio channell's RSSI to switch on "free" channel.
How to make it properly?
This is my code:
if(rx_q_flag == true){
err_code = esb_init(RX,...
I want to increase the MTU values to increase the throughput from my own service (currently based on NUS service) and to receive the data with pc-ble-driver-python with the...
I am using power_manage function to keep low power sleep mode. And I used below peripherals in code,
SPI master, SPI master is disabling when ever I am not using.
...
It appears to me that some of the saadc APIs (e.g. those found in nrf_drv_saadc.h in SDK 1.4.0) are missing in the nrf SDK for HomeKit.
Some hint where to find these functions...
How do you do
The attachment is a problem in the previous code, please help to debug it, thanks ble_app_uart_pwm.rar
E:\nordic\nRF5_SDK_12.2.0\examples\ble_peripheral\ble_app_uart_pwm...
Hello.
There is an executable file built by setting the address of the entry point (RO_Base) to 0x00000000 with Keil's linker setting.
I converted this executable file...
Hi,
I'm using nrf52840 with openThread. I like set the MCU in system on low power mode. RTC1 is used as application timer for wake up and start transmission periodicly. For...
Hello,
I could not find any related info, so I would like to ask few questions:
I have pca10028 board, using s110, sdk 6, ble_app_uart code. The board gets connected...
