I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
is it possible to atomically change both the GAP address and the advertising message in one step? I want to broadcast two different advertising messages with each of...
hi,
please any one explain me, what is the use of power registers of module such as UART, SPI, ADC,GPIOTE etc..
1.NRF_GPIOTE->POWER
2.NRF_ADC->POWER
3.NRF_UART0-...
Hi guys, now i have done the example as the light control demo description, but i have a question about that how i can let the light server to leave the network? Thank you...
A little background with this question
So, long story short:
To send data using notification, in android, you must first enable CCCD descriptor of matching attribute...
we have made 51822 communication with 24LU1+ successfully, result is 32payload, 2Mbps, 800FPS。
however, after add freeRTOS, our 2.4G will lost 5-8 packets and disconnected...
Hello,
I'm having a lot of trouble debugging some errors on UART. I'm initializing the UART as follows:
void uart_init()
{
ret_code_t err_code;
const app_uart_comm_params_t...
Hello Everyone,
I'm a beginner for nRF52 and my aim is to learn and develop system on nRF52. I have bought nRF52 development board and installed Keil MDK on my system....
I have to talk to a SPI device, which gets an address and then needs some time to handle the address. Afterwards the transfer can continue.
Is this scenario possible to...
timpwmadc.c
It is perfect (wonderfull!) idea to use programmable system PPI (EEP->TEP+FORK) alternative
PGA.
But I get some problems:
I tried to program a TIM3 to...
Hi,
Is it possible to call an arbitrary function at a breakpoint in gdb on the nRF52? I know you can with normal gdb, but I haven't been able to make it work with the cross...
Hi
I have a project to model the RSSI based indoor location using Bluetooth beacons. However, in order to do the basic distance and RSSI relation, I want to sense the channel...
Hi, im using nRF 52 DK. I interfaced mpu 6050 by using the example found here (BLE example found here is not working properly, dosent connect with uart app). I'm particularly...
Hi,
Does the erase target in the makefile completely erase the flash? I'm having strange errors when trying to read the flash (i.e. I can't read anything from flash, even...
Hi, Schematic and Code As shown above, VCC 3V (DEC2 and VCC open) current is only 3.8uA, but VCC 1.8V (DEC2 and VCC short circuit) current exceeds 1mA, what am I mistaken...
