Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
hello I'm Mehdi. i work on two NRF24lL01 wireless modules. I have a doubt that this modules can be damaged or not work correctly. because the module don't give external interrupt...
Hi!
I am trying to make basic temperature nodes with nRF2402.
The receiver is nRF24L01 transceiver.
My question for nRF2402; is it possible to send config bits via...
Hello,
Recently I've begun updating to the new SoftDevice and SDK for the nRF51822. When I began debugging my migrated code with the development dongle and Master Control...
I'm looking for a little guidance in figuring out why I get this error now when I call SOFTDEVICE_HANDLER_INIT. It appears that I get the error above at the end of softdevice_handler_init...
Dear nordic guys,I'm developing with nrf51822.
I have one simple question.
I want trying to connection request at the BLE server side to BLE client with previous connected...
I noticed that m_sec_params passed to sd_ble_gap_authenticate(uint16_t conn_handle, ble_gap_sec_params_t const * const p_sec_params) has been declared as a static variable...
Hello
I was trying to make an example program for a Client. And when I was searching for the sd_ble_gap_scan_start function I didn't find it. Altough in the documentation...
I am getting an NRF_ERROR_INVALID_PARAM when calling sd_ble_gatts_characteristic_add. This is the 12th characteristic added and follows the same general style of numerous...
This question relates to the unofficial gcc Makefiles available here:
github.com/.../nrf51-pure-gcc-setup
Using these to build a project based on the sample proximity...
Hi,
I just tried to toggle a led when a particular button in the evaluation board (nrf51822) is pressed, i just referred the gpiote sample code and started modifying it...
Hello,
I'm working on the nrf51822 with s110 stack and 5.1 SDK.
Wy functions are not described in the documentation but just enums and data types ?
I'm looking for informations...
I'm wrote a simple test to persist data using pstorage.
But I'm unable to load the stored data.
I'm using gcc and debugging with gdb. So I can see that storage_cb_handler...
Hi,
I am working on a project where there are moving devices. Devices can only move if a wired button is pressed. In fact, for security reasons, there are two buttons connected...
I've been looking at this for the better part of a day and can't seem to pinpoint what I'm doing wrong here. Does anybody want to take a quick peek at this project and tell...
Hi,
I would like to use the PCA10000 dongle hardware and antenna design for my PCB, i got some questions:
1)I have just UART pin outs extra, I would like to reduce the cost...
