Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
i just purchased the www.xcluma.com/bluetooth-4-0-module-NRF51822-2-4G-module-development-board-ble-4-0 this xcluma nrf51822 module , so how can i progarmme it . which IDE...
Hello,
I've noticed the following sentence in s132_nrf52_3.x.x release notes:
"Synthesized low frequency clock source is not tested or intended for use with the BLE...
I'm following the tutorial in the NRF52840 SDK on setting up a Thread Border Router here and I've run into some issues during testing. For one, I'm trying to resolve ipv4...
Hi,
I'm able to successfully enable Access Port protection, either using nrfjprog or by setting NRF_UICR->APPROTECT register to 0xFFFFFF00 in code.
But I have a problem...
Hello,
Since this seems to be a very hard topic to find info about (its very contradictory and confuse) I'd like to ask a Nordic employee directly.
I'm planning to build...
This concept keeps popping up when I'm dealing with mesh networking.
My guess is that, to avoid air collision, packets/pdus are sent on a randomized or predefined combination...
Hi,
I am using ble_app_uart for my development, in that I have buffer size of 2kB which will store all the incoming data and the data will be processed and send over NUS...
Hi all,
I am using an NRF52 and SDK 13.0
I have an external device (central) that I am connecting to using my (peripheral) device.
My peer manager set up is
#define...
Hello All,
I've got two Rigado development boards that I'm programming with KEIL uvision 5. I've tried a few examples, for example: blinky, which program and work fine...
Hello
I want to clarify the exact meaning of the carrier test or unmodulated signal in DTM.
In carrier test mode, DUT transmits 0xFFF....FFF which means all one pattern...
Hello,
For my project I need to measure the battery voltage while transmitting data to get a good indication of the battery capacity. I've found an old example ( link text...
Hi,
nRF24L01 seems like a perfect choice for home automation project that I have in mind .. I will have to install about 20 of those around the house.
My question is...
Hello,
I'm working on the bootloader using SDK13.1. In the file dfu_req_handling.c there is a variable called m_flash_operations_pending that gets incremented with every...
