Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I have a project where specification requires disconnecting immediately after sending a response to a BLE read request. I'm using authorized reads.
Currently, I'm using...
Hello,
I am measuring 5~6 mA of current consumption in standby mode, even when not broadcasting/connected. Why is it so high?
Aditional info:
I am using a custom...
I am using IAR workbench. Using softdevice s110 Version 7.
I have created a bootloader at memory address 0x3A000.
My application sits at 0x16000.
My application checks...
I used the sample code from nordic with nRF51822. DTM works fine. sensibility test gives me 0% on the 3 channels. Perfect.
Then I copied and paste into my code, calling...
I'm compiling and running correctly but the Keil software program for St- Link does not work I have . Have a different method to compile and install nrf51822 ?
on iOS 9 beta 5, ANCS doesn't work.
Steps to reproduce:
On iPhone, Settings -> Bluetooth
Tap to connect and pair
Make a phone call on another device
no caller...
Good work,
I am trying to control with android i nrf51822 But I have a problem. Ten LEDs After connecting the device with Android when I press the off button or "device does...
redbearlab nrf51822 led controller with android.nrf51822 with android connected.But led on off Device does not support uart.Disconnecting.
How solving is the problem ?
I wrote code usenig de Development Board 10028 (nrf51422).
I bought in aliexpress This model link text
The first question I remember There is almost no difference between...
I have a project, where I try to trigger an interrupt when I get a low-to-high tranistion and high-to low transition.
My setup:
-nRF51DK
-SDK8.1
-SoftDevice 8...
I'm looking at the ble_app_hrs example and I'm confused about how the drivers are able to differentiate between events originating from various services/characteristics. For...
The JLINK is costs hundreds of dollars, the STLINK is less thank $20 USD (available on ST's Discovery boards). I would really prefer to use the STLINK. Is there a way to program...
I have two nRF24L01+, one as PTX and one as PRX.
Both have following config: EN_RXADDR = ERX_P0, EN_AA = ENAA_P0, RF_CH = 100, RF_SETUP = 0x26, SETUP_RETR = 0xF0, SETUP_AW...