Dear devzone, Can our nRF52840 detect 20 nanosecond voltage fluctuations using COMP? For example, if I set a lower threshold of 20mV and an upper threshold of 60mV, and the...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
In the documentation for the secure bootloader, it's mentioned that the provisioning data gets stored in OTP memory for some chips (e.g. nRF5340). Is there a way to know what...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
Device Overview
We have developed a smart wearable that sends notifications to our mobile application over BLE. Under normal conditions, the device alternates sensor...
Hi, I'm updating my code which used to have a direct handler GPIOTE_IRQHandler(void), however I can't seem to get this working.
The Kiel Run Time Management has a requirement...
I updated from SDK 8.0 to SDK 8.1. My project had both app_uart and app_gpiote. With 8.1 (I don't exactly remember how it was on 8.0 and I have not spent any time researching...
I wanna use a nrf51822 dongle to sniff all data packets sent by 4 to 6 beacons, without large loss. The code I use is a python api given here learn.adafruit.com/.../python...
I need to provide a battery level in the application I'm working on. This application's services will all be custom - I'm not using predefined BLE services.
Our device...
Dear Sirs,
I am currently developing a project using nrf51422. My programs works fine with pca10026 develop board.
I builded a custum PCB for my project. All HW components...
In the ble_app_hrs_c the scanning indication LED blinks with a periodicity of about 4 seconds, while the advertising LED on the peripheral blinks at the expected 2. Both systems...
Hi,
I am currently experiencing TWI module lock-up issues with the hardware TWI library, which is supposedly fixed according to PAN v3.0, issue #56. (The issue was previously...
Hello,
For me, at the moment there are two things unclear.
With the help of some Nordic examples, I was able to add a Service with 3 characteristics to the used S120 BLE...
Hello all,
I'm new to embedded development and could use some help here.
I am currently working on our own board with a nRF51822 chip on it and using SEGGER j-link to...
Hi,
I just got my nrf51 dk and my task is to connect it with a bluetooth device, say a bluetooth treadmill, and retrieve data from it. The bluetooth treadmill was designed...
hi, i'm trying to develop a wearable health device.
actually, the device is a little unusual because it is attached to the Armpit or sole of the foot or inside knee ..
...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello
I'm trying to diagnose a problem I have with my own hand-soldered nRF51822-QFAA based bluetooth proximity device. I have the PCA10028 development kit to compare with...
MasterEmulator Version 2.1.12.6,
PCA10000 Version 1.0,
MEFW nRF51822 version 0.9.0,
The log file shows the following;
12;18:17:38.4681 [] - - Start of script: (2015...
