Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
Hi all! May I use another quartz instead of 16 MHz? Will the output frequency equal to 2.4GHz/16, if I will be use the 1 MHz quartz? Or IC will not work? Is it possible to...
I need to evaluate the real consumption of current for BLE events on RF81822. The HFCLK is 16MHz and the 32kHz clock is external.
S110 Soft Device Specification V1.2 document...
Hi, I am using S120 1.0.0 and SDK 6.0.0. Learning the sample project 'ble_app_multilink_central'.
I already got a peripheral device with NUS service. The central device...
I am new to this great platform and am struggling with getting my PIR sensor connected to my DK. I wonder if some of you experts could give me some pointers on how to go about...
Hello, I build a BLE 6LoWPAN environment on my raspberry pi with Kernel 3.18.3 and connect a BLE Dongle. The BLE Node is Arch BLE ( www.seeedstudio.com/.../Arch-BLE-p-1998...
Hi, I have two different types of nRF24L01+ modules, both behave differently.
The "troublesome" module always has TX_DS asserted after a transmit, which is the same behavior...
Hi,
I am using the SPI Master 1 to control an EEPROM. I used the spi_example project to help get the code working. It all works fine if the code that initiates the SPI...
We have designed a differential antenna for the nRF51822 CEAA chip.
Each of the RF output connects through a matching circuit to each one of the two 50-ohm to ground end...
How to setup MQTT for CloudMQTT? I have working raspberry PI I can ping and connect to device when follow the user guide. Now I like to try MQTT example but don´t know how...
Is there a list of every interrupt these functions effect. Specifically I am worried about
static void ble_evt_dispatch(ble_evt_t * p_ble_evt)
My assumption is that...
Is there any S110 demo with good communication between periphera and APP in phone side in SDK 6.0? It means that data channle works well from 51822 to APP and APP to 51822...
Is there any S110 demo with good communication between periphera and APP in phone side in SDK 6.0? It means that data channle works well from 51822 to APP and APP to 51822...
The nRF51 series reference manual v3.0 documents 3 Real Time Counters: RTC0, RTC1 and RTC2 (pp 17 and 109). However, RTC2 does not appear in the SDK documentation (e.g. no...
when I download program(pin_change_int_example) in nrf51822, Immediate Interrupt is occured
And when I push the button, Interrupt is stop...
What is problem?
I want...
Hello,
I am designing a board based on the SoC nRF51822. Since this is a homemade project I do not have lab equipment so I can not measure antenna impedance and therefore...
