I am reaching out to seek your guidance on a development project involving the nRF52840 and Semtech SX1262 LoRa transceiver.
We are building a marine crew monitoring and...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
Hello we have developed a few products which have required (costly) RF/RFPHY testing.
Is there a reference design that is qualified that can be used to avoid the RF/RFPHY...
Suppose a BLE central needs to get sensor data from 10 peripheral sensors. Given that there is a limit to the number of connections a BLE central can have, is it better for...
Has anyone managed to get this revision of the nrf8001 IC working?
i bought 280 of them and none of them seems to work as it should.
When i reset the chip i get no interrupt...
I tried to download softdevice 8.0 and the example code of SDK8.0
(\nRF_Examples\8.0.0\dfu\bootloader\pca10028\dual_bank_ble_s110\arm5)
to PCA10001.
First I Copied the...
I'm devloping application on nRf51 for that i'm using... SDK : nRF51_SDK_7.2.0_cf547b5 Tool chain : GNU tools arm Embedded [arm-none-eabi version 4.9.3] Dev Board : PCA10028...
Along with S110 BLE stack I programmed my application, which I managed to do without any conflict.
My application is not working properly and neither control is transfered...
how much time of keep level HIGH/LOW can make nRF51822 detected the HIGH/LOW level and generate an interrupt?
how width of impulse need to generate an interrupt?
Hi Team,
I was trying to load firmware to external board using nRF51-DK.
I have successfully programmed the boards many times and now when I am trying, LED (LD5) on nRF...
Hi all,
I downloaded the nrf51SDK_.8.0.0 from nordic site and tried to flash the new softdevice s110 but failed. I used an android application to flash it over the air...
Hi:
i use ble_app_uart project and want to change the UUID lenth(128 bit) to be 32 bit;but i change "nus_base_uuid" to be 4 byte and change "uuid128[16]" to be "uuid128[4...
Hi,
Does hardware that has already a Qualified design Listing (Bluetooth.org) requires re-testing of the RF-PHY ?
(refering to transmitter tests (i.e TRM-LE/CA/01/C (output...
Hi,
Im using a module NRF24L01 + LNA bought off ebay, connected it to msp430 via SPI interface. All spi communications are going solid, I manage to completely configure module...
I am trying to create a file and write to it during runtime. When I use fopen with "w" option to create a new file, the file pointer is always retuned to be NULL.
Is there...
