Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
I need to add connectable beacon advertising data instead of normal advertising for proximity profile example (NRF52 DK -> PCA10040 ->S132 -> nrf52832).During Advertisement...
Hi,
We had a power issue with our custom board related to DFU updates. After performing a DFU we were seeing 8mA idle current, and when we had programmed the firmware directly...
Hello,
can you provide a best practice guide on how to use memory protection unit in nRF52832.
I am interested to know if MPU can protect user defined memory regions...
Hi,
I want to know Tx power and duty cycle information of Beacon and NRF52 for the following cases:
In our case NRF52 will be our receiver and Beacon will be transmitter...
During the CE immunity test, the nRF51822 has to re-connect automatically without user interaction when the BLE connection is blocken by noise. Please tell me how to implement...
hi,all
my device use CR2450 button battery,advertise time 500ms
TX POWER:4dbm,the battery life is low if it still use this configuration
(May be big current lead...
Hi all,
I am using a nRF52832 with SD S132 V4.0.2 ion SDK13.
My application currently uses TWI, SPI and BLE and also 1 wire (which is based on delays). Everything works...
Hi!
I am working with PCA10040 (nRF52), s132 and SDK 12.2.0.
I am using the example experimental_ble_app_eddystone.
I have configured one slot as TLM, so it reports...
Hello,
We're using JLinkExe for production programming. Is there an equivalent of the nrfjprog --erasepage command for JLinkExe?
I'm looking for the equivalent of
nrfjprog...
Hello,
I feel like this question has an answer similar to this question, but I can't seem to get it working devzone.nordicsemi.com/.../
I am using the nrf51422 chip...
Hello,
I bought a SainSmart display which fits on the PCA10028 development board. This display is a 16x2 character display with a HD44780 display contoller (I guess).
...
Hi,
i am new in nrf51822.
i want to make a pin as a external interrupt pin, whenever it get high to low pulse it will call in ISR.
here i am unknown how to write an ISR...
hi,
i have downloaded code to nrf52 BLE module using nr52 DK with VTG,SWIO,SWCLK connections. but here i am unable to display the log for nrf52 ble module. is it possible...
Hello, I got the solution for my previous errors, but now I'm facing new error, that now when I compile my code it gives error like invalid command name "nRF52"
ac2...
