Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
I need a cheap 2 or 3 button fob or itag to connect to/control my NRF51 firmware. So far I only could find "AB Shutter 3" as input device with >1 button but it is using Bluetooth...
Hi all ,
I have one question . I have 3 board NRF : 1 peripheral and 2 central board . I want to transmiss
data from peripheral board to central board 1 then from central...
I am reading a large FIFO buffer from a sensor and there are at least two ways to do it - by simply reading the FIFO using the CPU and SPI in chunks of 255 byte blocks, or...
Hi everyone,
I am having problems in getting the low power mode in SAADC to work.
If I enable it in the config file then the ADC doesn't run anymore.( Blank in the RTT...
HI
I've successfully executed the Light control example and remote provisioning example separately but would now like to combine the light control example with the the...
Hello!
i am testing the nrf52 ble uart example. i am able to communicate with the BLE smartphone application (rx and tx) but i cant seem to get printf commands to print...
Has anybody created a table of what SD consumes in term of Flash and RAM.
More specifically I need the resources taken by S332, which include BLE and ANT + DFU.
Regards...
we need to open uart 30s and close it 30s.there is our code:
if(sec_cnt==30)
{
//printf("sec_cnt=30 is now\r\n");//zzq
nrf_delay_ms(100);
nrf_drv_uart_uninit(&m_dtm_uart_driver...
hi
I write a function getT() to read spi thermalcouple chip.
if the function getT() is called in main() function, it will work correctly. Hence, I think that getT() is...
Hej allesammen!
I'm having trouble with the bootloader example "bootloader_secure_ble", which seems to stuck when calling nrf_dfu_mbr_init_sd. But one thing after another...
I'm using nRF5_SDK_14.0.0_3bcc1f7 and SD132 v5.0.0. In response a DATA_LENGTH_UPDATE_REQUEST event, I'm calling sd_ble_gap_data_length_update as follows:
ble_gap_data_length_params_t...
Hi,
I am using nRF52832 with S132 softdevice and SDK version 11. I am getting bad memory address error code.
err_code = sd_ble_uuid_vs_add (&base_uuid, &ble_service->uuid_type...
Hi
I have a softdevice assert problem when i run the "nrf5_SDK_for_Mesh_v0.10.0-Alpha_src\examples\light_switch\client\light_switch_client_nrf52832_xxAA_s132_5_0_0.emProject...
we use
peripheral: exemple ble_app_blinky
central: exemple_ble_app_bliky-c
Instead of a button we have a Switch.
When we set the Switch to "on" the led go on.
That...
