here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Good Afternoon,
I hope someone can point me in the right direction.
We've customised an NRF51822 beacon and made it into a sensor but there seems to be an strange error...
Hello all , please your help
I need please , a reference design of nRF51822 for minimum with CR2032 .
using a pcb antena . ( distance is 4M) + the JTAG lines ...
Hi,
I am trying to secure OTA in nrf51822 board.
For that trying to build bootloader file available in SDK 12.2.0 version at location nRF5_SDK_12.2.0_f012efa\examples...
Hello,
I'm working on a project for which I would like to interface bno055 with nrf51822 smart beacon using i2c/uart. Basically the beacon must extract sensor values from...
With calls to these functions:
nrf_drv_gpiote_init()
nrf_drv_gpiote_in_init()
nrf_drv_gpiote_in_event_enable()
I have a handler (interrupt) routine that services a CAN...
I want to create a whitelist on the Central device. Because there is a lot of peripheral devices around and I just want to connect one peripheral device. First I register...
We have been recommended to use RIOT OS for our application and have been going through the tutorials but it seems that accessing the GNRC API for low ping ip communication...
Hai
i am using mbed to program my nrf51822. i need to implement bonding in my application. for that i am using securitymanager. and i have changed DEVICE_MANAGER_MAX_BONDS...
I am facing the same issue regarding to this post "Custom Service Issue - devzone.nordicsemi.com/.../".
At least i could figure out the IRAM1 start and size as explained...
Hi there!
I have been working with serializer and have the below issue:
I am using sd_ble_gatts_hvx() to transfer 20 bytes in burst until I get an error (TX buffer full...
Hi all,
first I have to admit that I'm a total rookie in "electricity". I know BLE software-side but just started to learn the hardware stuff.
I just received my PPK and...
by writing servals data into flash ,the data is always is 0,
void fstorage_test(void)
{
ret_code_t ret = fs_init();
if (ret != NRF_SUCCESS)
{
bsp_indication_set...
HI,
I am using nrf52832 with softdevice 132. Using SPIS1 to get the sensor datas from nrf to AARDVARK for calibration. Whenever I send the data's from aardvark(using AArdvark...
Whenever I try to flash the device in keil, I get a no Jlink device found. I get a similar message when trying to connect to the device via Segger. nrfGo Studio just does...
hello:
i want to use pwm in SDK9.0, in my project ,i need to send a cmd to nrf51822-QFAA,and then it control the motor on ,and with this cmd ,i should contrl pwm to let...
