Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi，
I am looking forward to ncs2.8.0, which was released last Friday. Today I tried nrf54l15 + 2-wire PA but failed to compile successfully.
sdk: ncs2.8.0
project: direct_test_mode...
In my project (SDK 2.9.1), I have configured a USB Mass Storage (MSC) device that uses a QSPI flash, like the one on the 52840DK board.
My system goes into sleep mode...
Hello,
I am using the nRF5340 in my project, and the device is capable of communicating with a mobile phone over BLE . However, we occasionally encounter a connection error...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi.
I've been developing with nRF54L15DK.
I added below in prj.conf.
Indeed, I could confirm CMSIS-DSP function normally running in main.c.
In my goal, I would like...
I have been testing nRF7002 in STA mode and in monitor mode. Both work fine - but is there a way to have both of them at the same time? Is this a feature that can be implemented...
Dear Sirs, This is about the software maturity levels of the nRF5340 Audio.
According to the page below, the Maturity level is set to ”Experimental” even in the latest SDK...
Nordic TS,
I'm trying to establish a link between two 9151 DK through which I can pass messages. I'm trying to create a setup where DK 1 receives messages using a DECT NR...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hello,
I recently acquired a Thingy91 board in order to make a hardware prototype. I already have experience developing with the nRF52840 so I took inspiration from my working...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
