I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am trying to send 20 notifications inside a loop. I am able to send 7 of these and receive the following error. What does this mean? Also, is there a central document that...
Hello,
We are facing a critical issue with our BLE peripheral product under development crashing during paring/bonding.
The phones used are all different, but the ones...
Hi all,
I want to know if the images inside the hci_dfu_send_hex folder are just precompiled hex files from the examples.
More specific I want to use the bootloader...
Hi
I have 3 nRF52840 DK, just shipped this week.
And two could power on success.
But one failed to power on after connecting with same USB cable.
The LDE5 did not...
Dear all,
I have designed custom board using Raytac mdbt40(nrf51822) module on my board and programming using nrf51DK my setup is like
VnRF: not used
VDD: not used...
He guys,
I'm currently trying to run the secure serial bootloader sample on our hardware which is based on the nrf52832, but the sample code resets the device when starting...
Hi
I develop nrf52840 and nrf52832 of our's RTOS environment(with. GCC).
I want apply mesh protocol with nrf52832 and nrf52840.
I ask,
when does support...
I try create my own app based on buttonless app. I've tested dfu over the air it's ok. But for that I need to firmware bootloader (with security key) before. It's ok for production...
Hi,
I dont get the Light Control example to work. Other examples from the normal SDKs are working.
I have 4x PCA10040 Dev-Kits.
I flashed the example with SEGGER...
We're having a range of issues with a firmware that I cannot detail due to NDA.
Hence we're looking for someone proficient with nRF51/52 using SD130/132 for reviewing/assisting...
Hi,
We can currently nRF51822 beacon kit. I want to know that do you have other beacon kit which have high range and in this large broadcast data can be broadcast ??
...
Good morning.
I use Google Translator to transcribe my articles.
Please understand if the context is not right.
I am currently testing HID Protocol with a mobile phone...
Hi guys,
i'm experimenting with ble_app_multiperipheral example from sdk14 and am having some issues.
I have made some modifications to be able to read and write characteristics...
Hello!
We experience problems trying to connect from Samsung Galaxy A5 (2017) to BL652-SC-01 module that runs serialization on a custom board: the smartphone is stuck at...
Hello, let it be clear that I could be wrong on this, but so far, based on the example provided by the nordic semi, I got the impression that the ble mesh is built almost...
