Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
I am performing automated testing on my device using an xml file that I have written. My xml contains a disconnect command. I observed that NRF connect reconnects to my device...
Hello,
After looking for pin mapping for TRACECLK and TRACEDATA[*] for nrf52840 I've seen 3 different mappings:
P0.07, P1.00, P0.11, P0.12, P1.09 in infocenter.nordicsemi...
Hi
I need to send as much data as it is possible in the advertisrment payload. Whem weset the devicename there are other fields that are automatically added to the payload...
I'm having issues executing any Zephyr project on a breadboard connected to a ISP1302. It works fine on the nRF51-DK but anything I try a final hardware nothing happens. Tried...
Hello,
I am using nrf52832 with PCA10036 V1.1.0. Soft device code is s132. I would like to know whether it will support Bluetooth 5.
I have downloaded nrf52 sdk13.0...
Hi, Dear Expert:
I am an Electronic Engineer. We used nRF51422 or nRF51822 at our products, but found the products was easily reset when did +/-1KV contact ESD testing...
now I used sample code of radio
change NRF_RADIO->MODE = (RADIO_MODE_MODE_Nrf_2Mbit << RADIO_MODE_MODE_Pos)；
In transmitter code , I change
while (true...
Story Short: When trying to run the ble_app_uart example on a custom board with a nRF51822QFAAH0 chip, the code faults and resets at the point in tries to call sd_softdevice_enable...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
Using:
nRF51822
GCC 4.8.4
Nordic Sdk 5.2.0
and even Ole Morten's nice pure-gcc setup
newlib-nano and -flto
Within the startup_nrf51.s I found something...
The server has no I/O, so no way to press a button.
Can an attribute cause the BLE to set a bit in Flash, so at the next power up, it will read that bit and know to execute...
Hello,
I followed the instructions of KEIL in www.keil.com/.../ulink2_trace_itm_viewer.htm
However, I cant get any outputs in Keil Debug(Printf) Viewer using printf...
I purchased a bunch of ptr8000 boards off ebay from china to do some testing of the nrf905 without realizing they were setup for 433mhz, and I need 915mhz. Looking at the...
Hi,
I am currently testing a DAC with I2S input supplied by the nRF52832.
But unfortunately no signal is coming out from the DAC, furthermore when reading the error registers...
