Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I would like to implement the mbed uVisor on the NRF52832 SoC with the softdevice s132.
So I created the configuration files and wrote some code.
Now I have problems with...
Hi,
I am trying to compile some RuuviTag application using nRF5_SDK_12.3.0_d7731ad
2 symbols are not defined,
APP_CONFIG_ADV_FRAME_SPACING_MS_MIN and
_ADV_FRAME_ETLM_SPACING_MS...
Hi nordic guys,
After the hid device delete the bond info but the PC did not remove it form the bond list,and i want the hid device to reconnect the PC quickly again but...
Hi,
in nrf connect app i see it is possible to update bootloader over ota.
How do i generate ota file properly? I tried generating zip and hex but the app says "no matching...
I have nRF6310, nRF2727.
I wonder if I can update the nRF24L01 firmware with the above board.
I wonder if there are any additional devices or other methods...
I am using ble_app_uart in one nRF52 EVK board(peripheral) and ble_app_uart_c in another nRF52 EVK(central) and sending data of Device under test through UART. When the data...
Hi,I want to use RTT in bootloader project.
First,i add all files(SEGGER_RTT.c ,SEGGER_RTT_printf.c,RTT_Syscalls_KEIL.c) to my bootloader project(Picture 1).
Second,I add...
hai
in nrf51822 the pins p0.01 t0 p0.06 are marked as analog pins in the nrf51822 DK.
i know that in arduino we can use an analog pin as an analog input as well as a digital...
Hello!
I am developing with mbed. According to nRFgo Studio, the hex file generated by the mbed compiler already contains the following SoftDevice: S132_nRF52_2.0.0 (Id...
Hi all, I'm working on sdk11.0.0 and s130 softdevice. In my project I want to send data coming from uart to ble and data coming from ble to uart same as ble_app_uart example...
Hi there,
I am working on programming the CTS ble service on my code.
In order to do that I also have to include db discovery.
#include "ble_cts_c.h"
#include "ble_db_discovery...
Hi,When I use nRF Connect app(IOS version) to connect my ble device,BLE_GATTS_EVT_SYS_ATTR_MISSING log information appears in my RTT Viewer(Picture IOS_Phone_Conncet).After...
Hello,
I tried as you mentioned using sdk12.1.0 buttonless_dfu and bootloader_secure example.
I didn’t modify anything except dfu_public_key.c.
As shown in the attached...
Hello,
I have a program that do an infinite loop in sd_softdevice_enable. How can i investigate ?
Loop is from 0x00009DEA to 0x00009DF2
Target is nRF52832 AA with...
Hi,
I am working on nRF52 with freertos + SDK13.0 + sd S132_4.0.2. I found the device will be trap in the xTaskIncrementTick of the xPortSysTickHandler when some task is...
