Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi,
I want to know what kind of antenna nordic recommend to use with NRF52 chips.
Please could you guide us about it. We are interested in some sort of table where we...
hello,
having everything working on the nRF52 DK i tried to migrate to the smart beacon kit (pca20006 with s130) but somehow cannot bring up a proper peripheral configuration...
Story and Official Code Test Passed
I am trying to integrate BLE into Smart-Lock and LoRa Terminal . So I build a custom board with off-the-thelf modules to evalute and...
I am current develop a "Surface Dial" hardware compatible device. (nRF51/S110)
Everything is ok but the host PC will freeze about 30 secs after my device wake-up from sleep...
I'm working on a product that is somehow related to geolocation. As part of it, RSSI measurement is sent back at high frequency to the central. Currently based on nRF51822...
Newbie here hoping to get some direction on how to properly setup a timer to have a timestamp displayed for DEBUG messages. I am working on a PCA10040 board. I tried looking...
Hi,
I have some basic doubts in installing the power profile on nrf52Dk(nrf52840). I'm trying to use it on my central device which has its application FW running. I have...
what is the sending data rate of the sd_ble_gatts_hvx() ,why i use sd_ble_gatts_hvx() send data 600Byte per second, it lost data again . it can be use yes or no ?????????...
I can copy a Hex file from a Mac to the mbed USB drive and the code executes correctly. However, if I upload the hex file from any windows PC in our office (Windows 10) the...
Hello, I am trying to generate pulses with the nRF52832 chip.I created a basic setup for test purposes; I simply connected a LED to the PWM output, but even though I put 0...
Hi,
I have designed the Circuit using NRF52832 BLE and AT8010-E2R9HAA RF ANTENNA and tuned the circuit accordingly. Since the antenna was not available so I placed other...
I'm relatively new to development on the nRF52832 and I'm trying to find information on how to use the sleep mode with the SAADC.
Goal: The micro should be in sleep mode...
Hi,
I am trying to create a BLE node which can perform dual role(advertising/scanning) to create mesh of multiple nodes. I am planning to do it with the help of timer....
the project has a problem with DMA,the detail is:
on the board,NRF52832 and extern chip communication with i2c bus,the chip through a pulse wake up nrf52832,NRF52832 start...
