It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello!
I hope this question has not been asked before - at least I can't find it.
I do have an application with two vender specific services (128bit UUID's) and I want...
Hi,
i am doing ble_app_beacon code on nrf 52832 with sdk 11 and s132. the packet, its advertising should only be received by the device whose bluetooth address we are providing...
main.c ble_uart.hex
Hello,
I use nRF5_SDK_11.0.0_89a8197 and s130_nrf51_2.0.0_softdevice configuration to test the ble_uart program.
i use nrfgo Studio to load the...
Hi Nordic team,
I try to use SDK for Thread v0.10.0 cli example and run diag command, but it is disable as below
Could you tell me how to enable diagnostics module...
Hi,
I'm using nRF52840. I would use data length extension and set the MTU size to 247 when it works as peripheral. However,there would be some problem when it connect to...
Hi guys,
I want to know whether the provisioning beacon can relay by the relay node or not?
If not, when the unprovisioned device's radio is not in the range of the...
Hi Sir,
I'm studying the nRF52840-PDK, and i found there are two debug connector. One is Debug in connector (P18) and another is Trace connector (P25).
As check the...
Hi!
I am fully aware on how Eddystone works. Or at least I believe so. Sadly there is some weirdnesses when I am trying to broadcast using the Nordic SDK.
So what am...
Hello , ebery one
Please let me have a question about PCA 10040.
When you connect a USB cable, it acts as a virtual drive and if you copy hex format (such as Hart rate...
I'm trying to determine DFU_APP_DATA_RESERVED and FDS_VIRTUAL_PAGES.
According to this Q&A, DFU_APP_DATA_RESERVED must be the same FDS_VIRTUAL_PAGES, if FDS_VIRTUAL_PAGE_SIZE...
Hello,
I am using pca10040 and sdk 12.2.2. I want that my pca10040 should advertise for 10 sec then it should go to system off mode then it should wake up after 20 sec. My...
Hi everyone,
I was wondering if the nRF52840 DK will have NCP OpenThread support for wpantund Linux (other than Raspberry Pi) or if it already exists. I flashed the nRF52840...
Hello ,
I want to establish a connection between the adxl345 nrf51822.
Nrf51822 is working both individually and Adxl345. I would be glad if I can provide you with necessrat...
We are building a new version of a small device with the new nRF52832. Its only external connection is a micro USB plug that we use for charging - we do not need it as USB...
