Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
These pins do not work when I connect to nRF51822 module directly..
Like this. I cennceted VDD, SWDIO, SWDCLK and GND to nRF51822 module.
And there are not jumpers to...
Is there any sample code in examples, because am a newbie to this great platform, my objective is to glow an led , when the motion is detected , and also when there is no...
Hi Sir,
I add NUS service into CSCS project base on nRF5_SDK_13 follow the steps below, there was no error occurred after build the project, but it didn't work. Please...
Hello,
I'm trying to set up I2C with an mCube cccelerometer, which has an I2C 7 digit ID of 0x6C and an 8 bit address (write) of 0xD8.
With the code below, I see on...
Hi.
I have a custom board, which I power up via AAA battery through a buck-boost converter. I wan't to measure battery level using on-chip ADC only on requests from master...
Hi there,
I've successfully sent the experimental buttonless dfu app "over the air" but now I am no longer seeing the option to DFU from within Nordic Connect.
Must...
Hi,
I'm using a PCA10040 board with the UART example provided with the v12 SDK, and the data seems to get corrupted somewhere along the way between my Ubuntu machine and...
My app works well when working with Master control pannel, but when I use nRF Connect (Android App of Nordic) I have a disconnection without any reason. Especially when I...
I want to send some data more than 20 bytes.
I use
ble_nus_string_send(&m_nus, tx_stuffed, 10);
3 times.
In the advertizer.c
in the function on_ble_evt
I insert code...
Hello,
I am trying to get to the bottom of a double-reset-problem which I am facing, whenever I flash my software-program to the nRF52832 (1 for the flashing and 1 after...
SDK Release Notes:
nRF5 SDK v13.0.0
Release Date: Week 11, 2017
Highlights:
Implemented a new license scheme for the SDK distribution. See the
documentation...
HELLO,
I want using sdk5.2.0/s110 6.0.0 update app in app.I only find BootLoader->app.How can I achieve it.
eg:I use my phone connect 51822 board,then send a command to...
Hi
I'm fighting to read characteristics of my service with sd_ble_gattc_char_value_by_uuid_read.
I'm using SD130 V2.0.1 and SDK11.
Here are some snippets from my central...
Need help from the mesh experts in this forum!
I'm running the open mesh in the 52832 with the s132_nrf52_3.0.0_softdevice.hex softdevice. The mesh works fine in my tiny...
