Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi,
I'm trying to communicate between a stm32f4 (spi master) and a nrf51822 (spi slave). I have configured the MISO, MOSI, CS and SCLK of the nrf. I use the spi_slave_example...
I'm using SDK 7.1, PCA10028 eval board, SD310 2.0.1
My application has no display, and a single button for input. I want to prevent bonding until the button is pressed...
I use Eclipse, gcc and OS X to compile.
I had FW working just fine with SD 6 and SDK 5.2. I recently tried to upgrade and ran into many problems, but the latest is the...
Hi
I've written an application that uses the gazell proprietary stack for nrf51822 and I want to use OTA-DFU using BLE.
Is it possible to upload the new firmware using...
I’m running into a problem with the SoftDevice safe twi that’s been posted in the forums a few times. I got the file here:
devzone.nordicsemi.com/.../
One of my peripherals...
Hello,
I have been messing around with a PCA10001 Dev board trying to do some power consumption tests (Beacon demo code). When I enable RTC1 only and use __WFE in the main...
Hello everyone,
I haven't read anything in the official documentation about it, but I was wondering if the S110 has an embedded checksum that I can use to verify its integrity...
Hi,
I'm currently working on nrf51822 beacon connected with stm32f4 board. able to communicate fine on UART as well as with bluetooth device. is there any way to find out...
We have been using the nRFgo nRF51822 development kit for prototyping. We now want to design our production board. However, your site says that this dev. kit is not recommended...
It seems these functions are identical in what they do, except that one is in S120 and the other is in S110.
Why not standardise the booting mechanism to facilitate code...
Hi !
I'm developing a bluetooth low energy service using the nordic evaluation kit and following the ble_lbs example. It works, but when I load the code on an other electronic...
Hello,
does the iOS Loader app not work with the nRF51422 chipset? I thought that this chip was more capable than the nRF51822. I do not seem to get access to the download...
I'm concerned about stack overflow as I consider using a linear fit function which declares 5 local variables as floats and accepts 5 pointers.
5floats * 4B/float + 5pointers...
