Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
The nRF54L series is a new device to the nRF family, and during the bring-up of the chip from early engineering samples to mass production devices there have been quite a...
Hi,
I currently have a problem with the continous scanning mode. I implemented the scanning mode that my device searches for the first 4 seconds after power up then picks...
Which example projects are compatible with s110 v7 for nRF51822?
I keep running into samples requiring "Legacy Keil" to be installed.
I just want a clean s110 v7 example...
Uint32_t data using sd_flash_write written many times to the same address, you must perform sd_flash_page_erase before writing it?
(English is not good, with Google Translate...
Is the DC/DC converter enabled when running ble_app_beacon?
Or is it only the LDO that is enabled?
I am running the application on nRF51822-DK.
BR Magnus
Hi,
I happily use the JLINK UART interface which show up as COMxx on windows for both the PCA10000 and PCA10001.
We are trying to 'see' the same on Linux. Have inatlled...
Could you please let me know the current rating in between retries while transmitting.From the oscilloscope reading, that is not obvious. The documentation shows three idle...
Hi
We had some problems updating our devices with the nRF Loader App on IOS. After selecting the device in DFU mode the App hangs and aborts with a Bluetooth error after...
Has anyone been able to get the DFU over the air bootloader to work with gcc and the newest SDK (6.0)?
I have followed all the tips I can find on here to get it working...
I'm wondering if the timeslot API is planned for the s130 or if it's intended to be s110 only. If it is eventually getting added to the s130 is there a loose time frame for...
Hello,
i am using the nrf51822 with softdevice s110. In the spec i read that the contoller works as well with an external 32khz reference which i want to use. The oszillator...
hello everyone,
i use nrf51822 and i want to use one switch that wakeup the module from sleep mode. so can i connect switch to gpio of nrf51822 module. if yes than which...
I'm a newbie so bare with me. I had this code running, saved it, and started another project. I tried not to touch any of the files I had running with the example below, but...
application note nAN-034 describes two alternatives for production testing an application using the nRF51822. One method is using a commercial tester (MT8852) and the other...
I need to send data PIR motion detector sensor to the master controller in my motion detector network.
Can I get away with just one of the nrf51 chips and my PIR sensor...
We're trying to decide at what voltage we should run our nRF51822 on the next revision of our board. To date we've been doing fine at 1.8V. The current drawn on a 3.7V lithium...
