I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
I have a single-ended signal that spans [0V,3.3V] and is centered around V_bias=1.65V (=3.3V/2).
I want to use the NRF54L internal gain to amplify only the AC parts of the...
this my yaml.file to use partition manager, beacause iam implementing DFU, USB MSC with fatfs in single project
fatfs_storage :
address : 0x00000000
size : 0x00200000...
Hi, I am using custom nrf52840 board with sysbuild, MCUboot+firmware loader, static partitioning, settings storage (OpenThread) and littleFS storage and I cannot get the thing...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Im trying to use the https://github.com/apache/mynewt-mcumgr-cli project to update my rfF54L15 with a DFU package
Setup: Raspberry PI 4 and and nrF52840 USB Dongle
I...
Help me please!!!
nRF52840 DK stops to scan after 3 hours working.
Project is based on central_nordic_uart_service.
Scan params
it works fine 3 hours and then BLE...
Hello,
I higly need to run twister unit tests in debug mode with breakpoints, step by step, spies and other debug tools in vscode. I did not find a way to do so.
Is...
Hello everyone.
WE're trying to make a https connection with google.com and execute a GET request.
Wifi connection is working; DHCP seems to be working (my personal assumption...
Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...
Hello,
I am working with the DWM3001CDK (nRF52833 + DW3110) using SDK 17.1.0 . I have successfully compiled and flashed the DTM example.
I am trying to use nRF Connect...
Hardware Setup:
Boar d: custom board using nrf5340dk_nrf5340_cpuapp
N CS Version: v3. 0.1 (upgrade d from v2. 4 where it was working)
Problem Description: After...
Hi,
I am wanting to talk to this external 1Mbit RAM chip through an SPI interface: https://www.microchip.com/en-us/product/23lc1024 with the nRF5340 device. Preferably,...
Hi,
I am trying to use the clangd extension with nRF Connect SDK, as it does a much better job than intellisense. I added
set (CMAKE_EXPORT_COMPILE_COMMANDS ON )
...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
